Cattron DYNAGEN ES52 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 27

background image

DynaGen

TM

ES52 - EN

User Manual

18

9M02-9253-A001-EN

Revision A

3.5.10 Warm Up

A Warm-up timer is provided on all ES52 series engine controllers. Terminal # 19 is the Warm-up timer output.

This output energizes 2 minutes after the engine running LED turns on (i.e., speed above crank disconnect

setting). When a stop signal is initiated, the Warm-up output turns off.
This Warm-up output can be used to control a load device; for example, allowing a generator to warm up before

connecting the load.

«
...
16
17
18
19
20
...
»

Содержание DYNAGEN ES52




























Отзывы:

Нет отзывов

Похожие инструкции для DYNAGEN ES52

Бренд: ZKTeco Страницы: 18

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Rane Страницы: 2

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: PUTCO Страницы: 2

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: Therma-Stor Страницы: 20

Бренд: FAIE Страницы: 5

Бренд: GEM Страницы: 31

Бренд: Waeco Страницы: 168

Бренд: LAUNDRY SOLUTION Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды