Cattron DYNAGEN ES52 Скачать руководство пользователя страница 10

Страница: 10 / 27

DynaGen

ES52 - EN

User Manual

9M02-9253-A001-EN

Revision A

Terminal #

Description

Start/Stop

when +12/24 VDC is applied, the controller is powered and proceeds to start

the engine. The power for the

crank output

and

fuel output

is obtained from this

terminal. If the 20A fuse is blown, then the ES52 will not start.

Fuel output

provides

10A

maximum. Fuel output closes to +12/24 VDC when start signal

is actuated, and it opens when either an engine failure is detected or when the stop signal

is applied.

Timer output

has one of four possible functions (Glow Plug,

Smart Choke

, Air-Gate or

Slow). This output closes to +12/24 VDC when activated.

Low oil pressure output

closes to +12/24 VDC when the engine shuts down due to a

low oil pressure condition. Flashing Low Oil output indicates an Auxiliary Input failure.

High temperature output

closes to +12/24 VDC when the engine shuts down due to a

high temperature condition.

Over-crank output

closes to+12/24 VDC when the engine shuts down due to an Over-

crank failure.

Over-speed output

closes to +12/24 VDC on an Over-speed failure and is open

otherwise. Flashing output indicates Loss of Speed Signal.

Engine running output

closes to +12/24 VDC when the engine speed is greater than the

crank disconnect setting, and it opens when the engine stops. Flashing output indicates

Crank Rest period.

Engine failure output

activates on any failure (closes to +12/24 VDC when activated).

Warm up output

turns on after the controller has been running for

2 minutes

and

seconds.

Output turns on immediately if battery voltage is applied to Start/Stop (terminal

10) and the speed is greater than the crank disconnect pot setting when the controller is

not cranking.

Note: Pins 12 to 19

The maximum rating of each output depends on how many outputs are on simultaneously on pins 12

to 19. Do not exceed these values:

1 on = 300 mA, 2 on = 230 mA, 3 on = 160 mA, 4 on = 123 mA, 5 on = 91 mA, 6 on = 80 mA,

7 on = 66 mA, 8 on = 52 mA

Good practice is to use 50% of the maximum rating.

Common ground

for annunciation outputs only.

DO NOT USE AS MAIN GROUND TO

CONTROLLER UNIT.

Содержание DYNAGEN ES52




























Результаты поиска

Содержание DYNAGEN ES52

Отзывы:

Похожие инструкции для DYNAGEN ES52

Бренды по названию

Популярные бренды

Cattron DYNAGEN ES52, Руководство пользователя

Результаты поиска

Содержание DYNAGEN ES52

Отзывы:

Похожие инструкции для DYNAGEN ES52

Бренды по названию

Популярные бренды