FEHLERSUCHE
BEHEBUNG
DER MOTOR LÄUFT NICHT AN, ODER ER FUNKTIONIERT SCHLECHT
- Kontrollieren, ob die Leitung der Luftzufuhr gedrosselt ist. Die extern an den Kolben montierten Dichtungen
POS.10
POS.10
DER EXPLOSIONSZEICHNUNG A00423
DER EXPLOSIONSZEICHNUNG A00423
sind verschlissen. Ersetzen! (kit KMYAK217/N). Zylinder und Kolben ausbauen
und schmieren.
DER HEBER HEBT DIE LAST NICHT
-Überprüfen, dass der Hahn
POS. 9 A00544
POS. 9 A00544
offen ist. - Den Ölstand im Tank durch die Schraube
POS. 24 A00347
POS. 24 A00347
kontrollieren.
- Es befinden sich Verunreinigungen unter den Ventilen : das Gehäuse entfernen, Hahn
POS. 9 A00544
POS. 9 A00544
schließen,
den Heber so umkippen, dass sich der Zylinder in horizontaler Position und die Motorpumpe in vertikaler Position
befindet, den Stopfen
POS.16 A00423
POS.16 A00423
abschrauben, die Kugeln und die Federn entfernen, das Innere sorgfältig
ausblasen. Alles wieder montieren, die Kugeln
POS.12 UND 14 A00423
POS.12 UND 14 A00423
gegebenenfalls wieder einschlagen, dann
erneut entlüften, wie auf der vorhergehenden Seite beschrieben. Den Heber wieder in die normale Position bringen
und den Hahn wieder öffnen.
- Den Hydraulikblock
POS. 2 A00544
POS. 2 A00544
kontrollieren und dabei besonders darauf achten, dass der Kolben
POS.4
POS.4
A00324
A00324
der die Ventile (
POS.7 A00324
POS.7 A00324
) zum Absenken öffnet und schliesst, nicht schwergängig geworden ist. In
diesem Fall ausbauen und fetten.
DER HEBER HEBT SICH, SENKT SICH ABER UNTER LAST AB
- Die Baugruppe
POS. 2 A00544
POS. 2 A00544
ausbauen und kontrollieren, ob sich Verunreinigungen unter der Kugel
POS.7
POS.7
A00324
A00324
befinden. Nach einer sorgfältigen Reinigung, die Kugel
POS.7 A00324
POS.7 A00324
mit leichten Hammerschlägen wieder
an ihren Sitz anpassen. Zum folgenden Punkt übergehen, falls die Last sich nach der Montage des Hebers noch
absenkt.
- Es befinden sich Verunreinigungen unter den Ventilen : das Gehäuse entfernen, Hahn
POS. 9 A00544
POS. 9 A00544
schließen,
den Heber so umkippen, dass sich der Zylinder in horizontaler Position und die Motorpumpe in vertikaler Position
befindet, den Stopfen
POS.16 A00423
POS.16 A00423
abschrauben, die Kugeln und die Federn entfernen, das Innere sorgfältig
ausblasen. Alles wieder montieren, die Kugeln
POS.12 UND 14 A00423
POS.12 UND 14 A00423
gegebenenfalls wieder einschlagen, dann
erneut entlüften, wie auf der vorhergehenden Seite beschrieben. Den Heber wieder in die normale Position bringen
und den Hahn wieder öffnen.
- Das Öl vollständig aus dem Tank und dem Zylinder ablassen, den Zylinder abschrauben und die Dichtung
POS. 10
POS. 10
A00347
A00347
kontrollieren; ersetzen, falls sie abgenutzt ist. Alles wieder montieren und dabei darauf achten, dass die
ersetzte Dichtung nicht zwischen Zylinder und Untergestell fällt. Den Tank bis zum richtigen Stand mit Öl füllen und
den Heber ein paar Male ohne Last bewegen; entlüften und dann bei abgesenktem Kolben den Ölstand wieder
herstellen.
DE
25
Содержание YAK 217/N
