manualshive.com logo in svg

Case Magnum 7210, Сервисный бюллетень, Страница: 7 / 26

Поделиться
Скачать
Case Magnum 7210 Скачать руководство пользователя страница 7

Service 

Bulletin NTR SB 026 96

Magnum Hitch Diagnostic Codes and Service Manual update
Page 7 of 26

These are the conditions (failures) that 

exist when the following codes are displayed. The codes 

are 

listed from the highest priority to

the lowest priority. When more than one failure exists simultaneously the highest priority failure will be displayed. All failures are

recorded in the controller (EEPROM) and can be retrieved in order of priority. See Reading and Erasing Error Codes.

CODE CAUSE MODE SOLUTION

Open or short (to ground). Lower coil or lower coil
circuit failure.

HALT

S

hort to 12 volt. Lower coil or lower coil circuit

failure.

HALT

O

pen or short (to ground). Raise coil or raise coil

circuit failure,

HALT

O

pen or short (to ground) of the raise and lower

coi

HALT

coils or relay contacts are open. Raise and lower
coil circuits failure, or relay circuit failed.

i 

EEPROM failure. 

The system cannot read

calibrated values or errors.

HALT

Tractor has not been calibrated. (Only appears
when controller has been replaced)

HALT Calibrate hitch controller.

1

Short to 12 volt, raise coil or raise coil circuit
failure.

I

HALT

Short to 12 volt, raise coil driver circuit. HALT Replace controller.

Short to 12 volt. lower coil driver.

HALT Replace controller.

Error code when calibration time is expired or the
boards memory is bad.

HALT

Replace coil.
Test wire harness for damaged wires or

connectors.

Replace controller.

rest wire harness for damaged wires or

connectors.

Replace coil.
Replace controller.

 

Replace coil.
rest wire harness for damaged wires or

connectors.

Replace controller.

Replace relay.
Replace coil.
Test wire harness for damaged wires or

connectors.

Replace controller.

Recalibrate controller.
Replace controller.

 

--

 

Test wire harness for damaged wires or

connectors.

Replace coil.
Replace controller.

 lb

Recalibrate controller.
Shut off key switch and restart tractor.
Replace controller

Содержание Magnum 7210



























Отзывы:

Нет отзывов