Case 48083741 Скачать руководство пользователя страница 58

Страница: 58 / 61

Engine - Engine and crankcase

19. Fix the end of the exhaust system pipe

(1)

to the en-

gine with a new clamp

(2)

. Tighten the clamp to

5.7 –

6.3 N·m

(

4.2 – 4.6 lb ft

LEIL17WHL0054AB

20. Install the alarm back-up

(1)

to the rear muffler support

with four bolts, washers (under bolt head and nut) and
nuts. Connect wire O_JB of connector BU1 to “NEG”
and

35 A

of connector BU2 to “H1”

(2)

of alarm back-

up. Secure the wire to the rear muffler support with
cable ties.

21. Install the fuel pre-filter support bracket

(3)

to the rear

muffler support with two bolts, washers (under bolt
head and nut) and nuts.

22. Install the fuel pre-filter

(4)

to the support bracket with

two bolts, washers (under bolt head and nut) and nuts.
At this time connect the GRD_WIF wire

(5)

by using

the same hardware.

23. Connect the WIF connector

(9)

and WSH connector

(6)

to the fuel pre-filter.

24. Use the clamp

(7)

to secure the fuel tank suction hose

to the rear muffler support.

25. Connect the fuel pre-filter to engine hose

(8)

to the

engine.

LEIL17WHL0055AB

26. Install the air intake cooling line

(1)

with clamps.

Torque the clamps

(2)

at the ends mating the charge

air cooler and engine to

10.1 – 11.3 N·m

(

7.4 – 8.3 lb

NOTE:

ensure clearance of

16.5 – 26.5 mm

between the

charge air intake tube and the muffler.

LEIL17WHL0090AB

48083741_EN 31/07/2018

10.1 [10.001] / 23

Содержание 48083741






























































Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды

Case 48083741, Руководство по обслуживанию

Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды