Case 48083741 Скачать руководство пользователя страница 55

Страница: 55 / 61

Engine - Engine and crankcase

7. Position the drive shaft on the engine coupling. In-

stall the six bolts (4–speed transmission) or eight bolts
(5–speed transmission) to secure the drive shaft to the
engine coupling.

NOTE:

the figure shows the machine with 5–speed trans-

mission.

LEIL17WHL0047AB

8. Tighten to

86 – 94 N·m

(

63 – 69 lb ft

) (821G, 4–speed

transmission).
Tighten to

85 – 94 N·m

(

63 – 69 lb ft

) (621G, 721G,

921G, 4–speed transmission and 721G 5–speed trans-
mission).
Follow the bolt installation pattern in figure.

LEIL17WHL1383AA

9. Tighten to

130 – 140 N·m

(

96 – 103 lb ft

) (621G, 821G,

921G, 5–speed transmission).
Follow the bolt installation pattern in figure.

LEIL17WHL1382AA

10. Install the upper and lower drive shaft dust covers.

Torque to

20 – 27 N·m

(

15 – 20 lb ft

LEIL17WHL0048AB

48083741_EN 31/07/2018

10.1 [10.001] / 20

Содержание 48083741






























































Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды

Case 48083741, Руководство по обслуживанию

Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды