Case 48083741 Скачать руководство пользователя страница 46

Страница: 46 / 61

Engine - Engine and crankcase

24. Tag and disconnect the ST, CPWR and battery posi-

tive cables

(1)

from the engine starter.

Tag and disconnect the negative battery cable

(2)

ground strap

(3)

and XM1C cable

(4)

from the engine

starter.
Tag and disconnect the GND_ENG1, GND_ENG3,
GND_ENG4

cables

(5)

and

GND_CENG1,

GND_CENG2 cables

(6)

from the engine.

LEIL17WHL0114AB

25. Tag and disconnect the breather line (hose and vent-

ing check valve) from the engine.

LEIL17WHL0094AB

26. Remove the U-bolt clamp to unfix the top cooling line

from the muffler support structure.

LEIL17WHL0095AB

27. Remove the clamps

(2)

to disconnect the top cooling

line

(1)

from the elbow hose and engine. Tag the hose.

LEIL17WHL0093AB

48083741_EN 31/07/2018

10.1 [10.001] / 11

Содержание 48083741






























































Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды

Case 48083741, Руководство по обслуживанию

Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды