Case 48083741 Скачать руководство пользователя страница 48

Страница: 48 / 61

Engine - Engine and crankcase

31. Tag and disconnect the fuel pre-filter to engine hose

(8)

from the engine.

32. Remove the clamp

(7)

that secures the fuel tank suc-

tion hose to the rear muffler support.

33. Tag and disconnect the WIF connector

(9)

and WSH

connector

(6)

from the fuel pre-filter

(4)

34. Tag and disconnect the fuel pre-filter

(4)

from the sup-

port bracket.
Tag the GRD_WIF wire

(5)

35. Remove the fuel pre-filter support bracket

(3)

from the

rear muffler support.

36. Remove the cable ties that secure the wires to the rear

muffler support.
Tag and disconnect the wires

(2)

from the alarm

back-up

(1)

Remove the alarm back-up

(1)

from the rear muffler

support.

LEIL17WHL0055AB

37. Remove the clamp

(2)

to disconnect the end of the

exhaust system pipe

(1)

from the engine.

LEIL17WHL0054AB

48083741_EN 31/07/2018

10.1 [10.001] / 13

Содержание 48083741






























































Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды

Case 48083741, Руководство по обслуживанию

Результаты поиска

Содержание 48083741

Отзывы:

Похожие инструкции для 48083741

Бренды по названию

Популярные бренды