background image

C

HAPTER

 1

2

Case IH Titan 4XXX - Steering Ready, Model Years 13 and Newer Raven SC1 HDU Guidance and Steering Installation Manual

GENERAL

• Always verify that the power leads are connected to the correct polarity as marked. Reversing the power leads 

could cause severe damage to the equipment.

• Ensure that the power cable is the last cable to be connected.
• A minimum of 12 VDC is required for system operation with a maximum of 15 VDC.

INSTRUCTIONS FOR WIRE ROUTING

The word “harness” is used to mean all electrical leads and cables, bundled and unbundled. When installing 

harness, secure it at least every 30 cm (12in) to the frame. Follow existing harness as much as possible and use 

these guidelines:

Harness should not contact or be attached to:
• Lines and hoses with high vibration forces or pressure spikes
• Lines and hoses carrying hot fluids beyond harness component specifications

Avoid contact with any sharp edge or abrading surfaces such as, but not limited to: 
• Sheared or flame cut edges
• Edges of machined surfaces
• Fastener threads or cap screw heads
• Ends of adjustable hose clamps
• Wire exiting conduit without protection, either ends or side of conduit
• Hose and tube fittings

Routing should not allow harnesses to:
• Hang below the unit
• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris, 

attachments)

• Be placed in areas of or in contact with machine components which develop temperatures higher than the 

temperature rating of harness components

• Wiring should be protected or shielded if it needs to route near hot temperatures beyond harness component 

specifications

Harnessing should not have sharp bends

Allow sufficient clearance from machine component operational zones such as:
• Drive shafts, universal joints and hitches (i.e. 3-point hitch)
• Pulleys, gears, sprockets
• Deflection and backlash of belts and chains
• Adjustment zones of adjustable brackets
• Changes of position in SC1 HDU and suspension systems
• Moving linkages, cylinders, articulation joints, attachments
• Ground engaging components

For harness sections that move during machine operation:

Содержание Titan 4 Series































Отзывы: