manualshive.com logo in svg

cascade corporation 20G, Оригинальное руководство пользователя, Страница: 21 / 24

Поделиться
Скачать
cascade corporation 20G Скачать руководство пользователя страница 21

19

6033701-R9 EN

PERIODIC MAINTENANCE

Carton Clamp Attachments

In addition to (or in place of, where necessary) the periodic 

maintenance found in the "General" periodic maintenance 

schedule (page 17), perform the following for Carton 

Clamp attachments:

 

1000-Hour Maintenance

•  Tighten accessible mounting capscrews and lower 

spacer capscrews (if equipped).  Double-torque 

capscrews by tightening to final torque value, loosen 1/2 

turn, then retighten.

12G–44G –

 270 Nm

IMPORTANT:

  If any capscrews are found loose, 

remove attachment from truck and check all mounting 

capscrews for proper torque values.

•  Tighten cylinder rod end anchor capscrews:

12G–18G –

 275 Nm

28G –

 110 Nm

36G –

 90 Nm

44G –

 275 Nm

•  Tighten contact pad capscrews to:

Standard (Shimmed) Design –

 65 Nm

Flexible (ADJUSTA-BLOCK) Design –

 90 Nm

•  Inspect lower frame wear tile for wear or damage.  

Replace as necessary.

CL3402.eps

Upper Arm 

Bearings

Upper Arm 

Bearings

Lower Arm 

Bearings

Lower Arm 

Bearings

Contact Pad Capscrews

Pivot Block 

Capscrews

Wear Shoe 

Capscrews

Cylinder Rod 

End Anchor 

Capscrews

Standard (Shimmed) Design

RH Side

Flexible (ADJUSTA-BLOCK) Design

RH Side

CL6015.eps

Cylinder Rod 

End Anchor 

Capscrews

Содержание 20G

























Отзывы:

Нет отзывов