Casals DBS900 Скачать руководство пользователя

Страница: 13 / 15

12.TROUBLE SHOOTING

Problem

Possible Causes

Solution

An unusually large
amount of sparks.

Damaged teeth.

Replace blades

Feed speed is too slow.

Increase feed speed

Blunt teeth.

Mount new set of cutter
blades

A lot of wear in sections.

Feed speed is too fast.

Reduce the feed speed

Damaged teeth.

Replace blades

Blunt teeth.

Replace blades

Not cutting parallel or perpendicular to
work surface.

Hold saw parallel to work
surface

Blades are breaking.

Damaged teeth.

Replace blades

Feed speed is too fast.

Reduce feed speed

Blunt teeth.

Replace blades

Blades have buckled.

Replace blades

Blades have burned out.

Replace blades

Broken blade teeth.

Feed speed is too fast.

Replace blades

The surface being cut is too hard.

Replace blades

The teeth have been damaged by
impact.

Replace blades

Blades were not installed properly.

Replace bladesand
follow the proper blade
installation instructions

Blades are burned out.

Replace blades

Not cutting parallel to work surface.

Replace blades and
always hold saw parallel
to work surface when
cutting

Содержание DBS900
















Результаты поиска

Содержание DBS900

Отзывы:

Похожие инструкции для DBS900

Бренды по названию

Популярные бренды

Casals DBS900, Инструкция по эксплуатации

Результаты поиска

Содержание DBS900

Отзывы:

Похожие инструкции для DBS900

Бренды по названию

Популярные бренды