Carrier XPOWER 38VYX050 Скачать руководство пользователя страница 8

GB - 7

38VYX050/38VYX080 

E N G L I S H

Minimum clearances

Open the upper side and both right and left sides.

The height of obstacle at both front and rear side, should be lower than the height of the outdoor unit.

1000

or more

150

or more

Serial installation of two or more units

1000

or more

1500

or more

2000

or more

200

or more

300

or more

Obstacles at both front and rear sides

Standard installation

Single unit installation

300

or more

200

or more

300

or more

1000

or more

Open the upper side and both right and left sides.

The height of obstacle at both front and rear side, should be lower than the height of the outdoor unit.

Serial installation at front and rear sides

Standard installation

38 VYX 050

38 VYX 080

ø 28 Drain hole

90

600

90

115

330

310

76

Drain
hole

Knockout
hole

Drain nipple
mounting hole

600

150

150

430

400

365

Installation

• Before installation, check strength and horizontality of the base so

that abnormal sound does not generate.

• According to the following base diagram, fix the base firmly with

the anchor bolts.
(Anchor bolt, nut: M10 x 2 pairs)

15 mm or less

Set the out margin of the anchor bolt to 15mm or less..

Содержание XPOWER 38VYX050















Отзывы: