Carrier TRANSICOLD 69UG15 Series Скачать руководство пользователя страница 22

Страница: 22 / 60

−

T-343

SECTION 2

OPERATION

2.1 GENERATOR SET INSTALLATION

The generator set is mounted under the center of the

trailer chassis and is easily handled with a fork lift truck

capable of handling 2,000 pounds. The fork lift pockets

provided are accessible from either side. Mounting

clamps are designed to be attached to outside I-beam

flanges only. Maximum chassis width is 38 inches on

center.
a. Standard Mount

1. Loosen mounting bolts (see Figure 2-1) sufficient

to push mounting plates to the outermost position.

2. Place forks into fork lift pockets of generator set.

Attach safety chain between unit and fork truck.

3. Center generator under chassis slide mounting

plates fully onto chassis I-beams and torque

mounting bolts to 80 - 90 ft-lbs (11.1 - 12.4 mkg).

Upon completion, remove safety chain before re-

moving forks of fork lift truck from unit.

b. Quick Mount

1. Loosen mounting bolts (see Figure 2-2) sufficient

to bring clamp to open position. To orient in open

position, lift nut end of bolt out of slot. Clamp will

fall open.

2. Place forks into fork lift pockets of generator. At-

tach safety chain between unit and fork truck.

3. Center the generator set in desired position under

chassis.

4. Lift clamp (item 1) in place, ensuring bolt (item 4) is

secured in slot.

5. Tighten bolt to 55 - 65 ft-lbs (7.6 - 9.0 mkg).

6. Upon completion, remove safety chain before re-

moving forks of fork lift truck from unit.

REAR OF CHASSIS

SECTION A ‐ A

ROADSIDE VIEW

FORK LIFT POCKET

CONTAINER FLOOR CROSS I-BEAMS

1. Bolt

2. Washer, Spherical, Male

3. Mounting Plate

4. Generator Frame

5. Washer, Belleville

6. Washer, Spherical, Female

7. Tee Nut

8. Roll Pin

Figure 2-1 Generator Set Mounting

−

Standard Mount

Содержание TRANSICOLD 69UG15 Series





























































Результаты поиска

Содержание TRANSICOLD 69UG15 Series

Отзывы:

Похожие инструкции для TRANSICOLD 69UG15 Series

Бренды по названию

Популярные бренды

Carrier TRANSICOLD 69UG15 Series, Операция и обслуживание

Результаты поиска

Содержание TRANSICOLD 69UG15 Series

Отзывы:

Похожие инструкции для TRANSICOLD 69UG15 Series

Бренды по названию

Популярные бренды