manualshive.com logo in svg

Carrier TRANSICOLD 69UG15 Series, Операция и обслуживание

Поделиться
Скачать
Carrier TRANSICOLD 69UG15 Series Скачать руководство пользователя страница 37

4

−

6

T-343

b. Winding Insulation Testing

Continuity test results for the stator winding tests are

provided in the following table:

Wire

Pair

Ohm*

Wire

Pair

Ohm*

Wire

Pair

Ohm*

T10-T1

I

T1-T8

I

T4-T5

I

T10-T2

I

T1-T9

I

T4-T6

I

T10-T3

I

T2-T3

I

T4-T7

I

T10-T4

I

T2-T4

I

T4-T8

I

T10-T5

I

T2-T5

0

T4-T9

I

T10-T6

I

T2-T6

I

T5-T6

I

T10-T7

0

T2-T7

I

T5-T7

I

T10-T8

0

T2-T8

I

T5-T8

I

T10-T9

0

T2-T9

I

T5-T9

I

T1-T2

I

T3-T4

I

T6-T7

I

T1-T3

I

T3-T5

I

T6-T8

I

T1-T4

0

T3-T6

0

T6-T9

I

T1-T5

I

T3-T7

I

T7-T8

0

T1-T6

I

T3-T8

I

T7-T9

0

T1-T7

I

T3-T9

I

T8-T9

0

* 0 = no resistance (closed circuit) & I = infinite  resistance (open circuit)

c. Diode Testing

The rectifier diode assemblies can be tested, and if

damaged, replaced. Over current, over voltage, over

speed, or reverse currents can damage the assembly or

diodes. To remove the diode assemblies and perform

diode testing, do the following:
1. Remove the bearing cover by removing the four bolts

(see Figure 4-8). Both the bearing and diode assem-

blies will be visible.

2. Mark and disconnect the alternator rotor wires at the

rectifier screw terminals. Note that the terminals are

marked with red paint for the forward diode assembly

and black for the reverse diode assembly. Mark and

disconnect the exciter leads from the double spade

terminals (see Figure 4-7).

a.

d.

c.

b.

a.

b.

d.

a. Diode Assembly

b. Diode Bridge

c. Exciter Rotor Lead Connection

d. Alternator Rotor Lead Connection

Figure 4-7 A-C Generator Rectifier Assembly

3. Remove the two cap screws that secure each diode

assembly to the exiter. Once this procedure is com-

plete, the diode assemblies are free for removal.

4. A forward diode should have a low resistance when

the + of an ohm meter is connected to the exciter ro-

tor lead connection (anode) and the - to the diode

bridge (cathode), and a high resistance when the po-

larity of the ohmmeter is reversed.

5. A reverse diode should have a high resistance when

the + of an ohm meter is connected to the exciter ro-

tor lead connection (anode) and the - to the diode

bridge (cathode), and a low resistance when the po-

larity of the ohmmeter is reversed.

6. If both resistances are high or both are low, the diode

is defective and the diode assembly should be re-

placed.

4.5.3 Bearing Replacement

When operated under normal conditions,

factory

−

lubricated shielded bearings will normally

provide years of trouble

−

free service. Excessive

bearing load and adverse environment conditions will

greatly shorten bearing life. To remove the bearings, do

the following:
a. Remove bearing cover and mylar gasket. (See

Figure 4-8).

b. Remove bearing with a bearing or wheel puller.
c. Install new bearing. Ball bearings are pre-lubricated

and require no additional lubrication for the life of the

bearing.

d. Coat mating surface of bearing cover flange with

anti-corrosion compound (Tef-Gel, Carrier Part

Number 02-00083-00).

e. Replace bearing cover and mylar gasket.

a.

h.

g.

e.

d.

c.

b.

f.

a. Rectifier Flange

b. Rectifier Assembly

c. Rectifier Bolt

d. Bearing Cover

e. Bearing Cover Bolt

f. Mylar Gasket

g. Bearing

h. Bearing Cover Flange

Figure 4-8 Rectifier Removal

Содержание TRANSICOLD 69UG15 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды