manualshive.com logo in svg

Carrier Infinity SYSTXCCUIZ01, Инструкция по установке и запуску

Поделиться
Скачать
Carrier Infinity SYSTXCCUIZ01 Скачать руководство пользователя страница 3

DECORATIVE BACKPLATE — Supplied is a thin decorative
backplate (see Fig. 5), to hide any marks/screw holes left from the
previous thermostat. This decorative backplate (or beauty ring) can
be used in either the recess or surface mount installation by
snapping it onto back of recessed mount backplate or surface
mount backplate before securing to wall. See Fig. 8 and 9 for a
larger decorative backplate P/N SYSTXXOLBP01 (5.75

″

wide X

6

″

tall), which can be ordered separately.

STEP 3 — INSTALLING INFINITY ZONE CONTROL™

ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Before installing Infinity Zone Control™, turn off all power
to equipment. There may be more than one power source to
disconnect.

1. Turn off all power to equipment.

2. If an existing User Interface or control is being replaced:

a. Remove existing control from wall.

b. Disconnect wires from existing control.

Fig. 2—Infinity Zone Control

A03185

Fig. 3—Recessed Mount Backplate

A03186

Fig. 4—Surface Mount Backplate

A03187

Fig. 5—Thin Decorative Backplate

A04017

Fig. 6—Recessed Mount Assembly

A03190

Recessed terminal
block in wall 1

1

/

2

˝

wide by 2 

1

/

8

˝ high

Recessed Mount

Interlocking Tabs (4)

Fig. 7—Surface Mount Assembly

A03191

Surface Mount
Backplate to wall

Interlocking Tabs (4)

3

Содержание Infinity SYSTXCCUIZ01

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды