background image

58MTB

Deluxe 4–Way Multipoise 2-Stage

Condensing Gas Furnace

Installation, Start-up, and Operating Instructions

Sizes 060-120, Series 100

NOTE:

Read the entire instruction manual before starting the

installation.

NOTE:

This furnace can be installed as a

direct vent (2-pipe)

or non-direct vent (1-pipe)

condensing gas furnace.

This symbol

indicates a change since the last issue.

TABLE OF CONTENTS

SAFETY CONSIDERATIONS .....................................................2

CODES AND STANDARDS........................................................3

Safety.........................................................................................3
General Installation...................................................................3
Combustion and Ventilation Air ..............................................5
Duct Systems ............................................................................5
Acoustical Lining and Fibrous Glass Duct..............................5
Gas Piping and Gas Pipe Pressure Testing..............................5
Electrical Connections ..............................................................5

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........6

INTRODUCTION ..........................................................................6

APPLICATIONS............................................................................6

General ......................................................................................6
Upflow Applications.................................................................6
Downflow Applications ............................................................8
Horizontal Left (Supply-Air Discharge) Applications ..........10
Horizontal Right (Supply-Air Discharge) Applications ........11

LOCATION..................................................................................14

General ....................................................................................14
Furnace Location Relative to Cooling
Equipment ...............................................................................15
Hazardous Locations...............................................................15
Furnace Location and Application .........................................15

AIR FOR COMBUSTION AND VENTILATION ....................16

INSTALLATION .........................................................................19

Leveling Legs (If Desired) .....................................................19
Installation in Upflow and Downflow
Applications ............................................................................19
Installation in Horizontal Applications ..................................19
Air Ducts.................................................................................19

General Requirements .......................................................19
Ductwork Acoustical Treatment .......................................21

Supply Air Connections ....................................................21
Return Air Connections.....................................................21

Filter Arrangement..................................................................21
Bottom Closure Panel.............................................................23
Gas Piping...............................................................................24
Electrical Connections ............................................................25

115-V Wiring.....................................................................25
24-V Wiring.......................................................................27
Accessories ........................................................................27

Removal of Existing Furnaces from Common Vent

Systems ..............................................................................28

Combustion-Air and Vent Pipe Systems ...............................28
Condensate Drain....................................................................42

General...............................................................................42
Application.........................................................................42
Condensation Drain Protection .........................................43

START-UP ADJUSTMENT AND SAFETY CHECK ..............43

General ....................................................................................43
Prime Condensate Trap With Water ......................................44
Purge Gas Lines......................................................................44
Sequence of Operation............................................................44

Two-Stage Heating With Single-Stage Thermostat
(Adaptive Mode)................................................................45
Two-Stage Heating With Two-Stage Thermostat
(Non-Adaptive Heating Mode) .........................................45
Cooling Mode ....................................................................46
Thermidistat Mode ............................................................46
Continuous Blower Mode .................................................50
Heat Pump .........................................................................50
Component Self-Test.........................................................50
Operate Furnace.................................................................51
Furnace Restart ..................................................................51

Adjustments.............................................................................51

Set Gas Input Rate ............................................................51
Set Temperature Rise ........................................................56
Adjust Blower Off Delay (Heat Mode)............................57
Set Thermostat Heat Anticipator ......................................57

Check Safety Controls ............................................................57
Checklist..................................................................................58

A93040

Visit www.carrier.com

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Book 1

4

Tab

6a 8a

PC 101

Printed in U.S.A.

Catalog No. 58MTB-1SI

Pg 1

8-05

Replaces: 58MTA-8SI

Содержание 58MTB





























































Отзывы: