Carrier 48PG24 Скачать руководство пользователя

Страница: 57 / 112

Alert Code T412 (W2 without W1) — This alert occurs in

Thermostat mode when W2 is energized and W1 is not. Verify

thermostat and thermostat wiring. When W2 turns On, the soft-

ware will behave as if W1 and W2 are both On. When W2

turns Off, the software will behave as if W1 and W2 are both

Off. This alert resets automatically when W1 is turned On.
Alert Code T413 (Y and W Simultaneously) — This alert

occurs in Thermostat mode when Y1 or Y2 is energized simul-

taneously with W1 or W2. Verify thermostat and thermostat

wiring. The software will enter either the cooling or heating

mode depending upon which input turned on first. This alert

resets automatically when Y1 and Y2 are not on simultaneous-

ly with W1 and W2.
Alert Code T414 (Economizer Damper Actuator Out of

Calibration) — This alert occurs when the economizer range

of motion is less than 90 degrees. Initiate economizer calibra-

tion (

Service Test

→

INDP

→

E.CAL

) using the Service Test

menu. The economizer calibration procedure will try to find

new maximum open and closed positions. If the alert does not

clear automatically after the calibration procedure is complete,

investigate what is limiting economizer rotation. This alert re-

sets automatically.
Alert Code T414 (Economizer Damper Actuator Torque

Above Load Limit) — This alert occurs when the actuator

load is too high. Investigate to determine what is increasing

damper load. This alert resets automatically.
Alert Code T414 (Economizer Damper Actuator Hunting

Excessively) — This alert occurs when the commanded

damper position is changing too rapidly. This alert resets

automatically.
Alert Code T414 (Economizer Damper Stuck or Jammed)

— This alarm occurs when the actuator senses it can no longer

move. Investigate what is stopping the rotation of the actuator

and fix. This alert resets automatically.
Alert Code T414 (Economizer Damper Actuator Mechani-

cal Failure) — This alert occurs when the actuator senses a

catastrophic failure. Investigate actuator and replace if neces-

sary. This alert resets automatically.
Alert Code T414 (Economizer Damper Actuator Direction

Switch Wrong Position) — This alert occurs when the econo-

mizer damper direction switch is in the wrong position.

The direction switch should be in the clockwise position and

the actuator should be mounted so that the CW face of the

actuator is accessible. Correct if necessary. This alert clears

automatically.
Alert Code T415 (IAQ Input Out of Range) — This alert oc-

curs when the IAQ input is less than 3.5 mA and the sensor is

configured as installed. Check sensor and wiring. This alert

clears automatically.
Alert Code T416 (OAQ Input Out of Range) — This alert

occurs when the OAQ input is less than 3.5 mA and the sensor

is configured as installed. Check sensor and wiring. This alert

clears automatically.

Cooling Troubleshooting —

Use the Scrolling Mar-

quee display or a CCN device to view the cooling status display

and the cooling diagnostic display (see Appendix A) for infor-

mation on the cooling operation. Check the current alarms and

alarm history for any cooling alarm codes and correct any causes

(see Table 43). Verify any unique control configurations per in-

stalled site requirements or accessories. If alarms conditions are

corrected and cleared, operation of the compressors and fans

may be verified by using the Service Test mode (see page 36 and

Table 36). See Table 44 for general cooling service analysis.

Humidi-MiZer™ Troubleshooting —

Use the unit

Scrolling Marquee display or a CCN device to view the

cooling status display and the cooling diagnostic display (see

Appendix A) for information on the cooling operation and the

related Humidi-MiZer operation. Check the current alarms and

alarm history for any cooling alarm codes and correct any

causes (see Table 43). Verify any unique control configurations

per installed site requirements or accessories. If alarm condi-

tions are corrected and cleared, operation of the compressors,

fans, and Humidi-Mizer valves may be verified by using the

Service Test mode (see page 36 and Table 36). In addition to

general cooling service analysis Table 44, see Table 45 for

general Humidi-MiZer service analysis.

Economizer Troubleshooting —

Use the unit Scroll-

ing Marquee display or a CCN device to view the economizer

status display and the economizer diagnostic display (see Ap-

pendix A) for information on the economizer operation. Check

the current alarms and alarm history for any economizer alarm

codes and correct any causes (see Table 43). Verify any unique

control configurations per installed site requirements or acces-

sories. If alarms conditions are corrected and cleared, operation

of the economizer may be verified by using the Service Test

mode (see Service Test section on page 36 and Table 36). The

following steps specify how to test the economizer using

the Scrolling Marquee display. See Table 46 for general econo-

mizer service analysis.

1. Enter the

Service Test

main menu on the display.

2. Enter

TEST

and turn ON test mode. A password may be

needed in order to turn ON the Service Test. The default

password is 1111.

3. Return to the main level of

Service Test

4. Enter the

INDP

submenu and enter an initial value for

ECON

. This will drive the economizer damper to the

specified position. Continue to adjust the

ECON

value to

make sure the economizer opens and closes.

5. Because of a mechanical problem with the economizer,

the actuator might acquire a new degree of rotation

which is less than 90 degrees. If this occurs, a “T414

Economizer Damper Actuator Out of Calibration” alert

will be generated. This alert can only occur if the econo-

mizer is using digital communications (

Configuration

→

ECON

→

E.CTL =

1 or 2

). The economizer calibration

procedure (

Service Test

→

IND.P

→

E.CAL

) will recon-

figure the actuator to the new fully closed and fully open

positions. To implement the calibration procedure,

change

E.CAL

from OFF to ON.

E.CAL

will remain ON

as long as the calibration procedure is being implemented

(as long as 5 minutes). During the calibration procedure

the actuator will close fully and then open fully. After the

calibration is complete, the degree of rotation should be

greater than 90 degrees, causing the T414 alert to clear. If

the T414 alert does not clear, check the economizer

damper for other mechanical problems.

6. Return to

Service Test

→

TEST

and turn OFF test mode.

This will cause the unit to return to normal operation.

Содержание 48PG24

















































































































Результаты поиска

Содержание 48PG24

Отзывы:

Похожие инструкции для 48PG24

Бренды по названию

Популярные бренды

Carrier 48PG24, Управление, пуск, эксплуатация, обслуживание и инструкции по устранению неисправностей

Результаты поиска

Содержание 48PG24

Отзывы:

Похожие инструкции для 48PG24

Бренды по названию

Популярные бренды