Carrier 38GVM Series Скачать руководство пользователя страница 30

Страница: 30 / 70

TROUBLESHOOTING CONTINUED

38GVM Diagnostic Codes

18, 24, and 30K

36 and 42K

Indoor Unit

Display

Indoor and/or

Outdoor Unit

Error

Defrost Mode 1

Outdoor

Defrost Mode 2

Outdoor

Inlet tube temperature sensor malfunction

See Error Code Table

Indoor

Outlet tube temperature sensor malfunction

See Error Code Table

Indoor

Low charge or refrigeration system blockage

Outdoor

Indoor return air temperature sensor
malfunction

See Error Code Table

Indoor

Indoor tube temperature sensor malfunction

See Error Code Table

Indoor

Outdoor ambient temperature sensor
malfunction

Outdoor

Outdoor mid---coil temperature sensor
malfunction

Outdoor

Outdoor discharge air temperature sensor

Outdoor

Cooling oil return cycle

Outdoor

System high pressure protection

Outdoor

Indoor freeze protection

Indoor

System low pressure protection

Outdoor

Compressor discharge high temperature
protection

Outdoor

Communication error between indoor
and outdoor

Indoor and

outdoor

Mode conflict

Indoor

System overload protection

Outdoor

Cold Blow Protection

Indoor

Test mode

Outdoor

Pump down mode

Outdoor

IPM Rest

Outdoor

Compressor current protection

Outdoor

Communication error between the inverter
drive and main board

Outdoor

Heat sink temperature sensor malfunction

Outdoor

IPM over temperature protection

Outdoor

Open Contactor

Outdoor

Current sensor malfunction

Outdoor

Current sensor mis---wiring protection

Outdoor

Input current protection

Outdoor

Inverter board ambient temperature sensor
malfunction

Outdoor

Low voltage protection

Outdoor

High voltage protection

Outdoor

Abnormal input AC voltage

Outdoor

Capacitor charging malfunction

Outdoor

Defrost or heating oil return cycle

Heating oil return cycle

Outdoor

Forced defrost

Outdoor

Compressor overheat protection

Outdoor

IPM Protection

Compressor speed reduction

Outdoor

PFC board protection

Outdoor

Compressor high voltage protection

Outdoor

Compressor start ---up failure

Outdoor

Compressor phase loss protection

Outdoor

Compressor stalling

Outdoor

Compressor over ---speed protection

Outdoor

Condenser coil inlet temp sensor malfunction

Outdoor

Condenser outlet temperature sensor
malfunction

Outdoor

Memory card error

Outdoor

Frequency limitation for module circuit
protection

Outdoor

Frequency limitation for module temperature
protection

Outdoor

Frequency limitation for overload protection

Outdoor

Frequency limitation for system circuit
protection

Outdoor

Frequency limitation for module circuit
protection

Outdoor

Frequency limitation for freeze protection

Outdoor

Compressor demagnetizing protection

Outdoor

Indoor and outdoor units mismatch

Outdoor and Indoor

Compressor phase detection malfunction

Outdoor

Low DC bus voltage

Outdoor

Communication error between main board
and EXV

Outdoor

Содержание 38GVM Series







































































Результаты поиска

Содержание 38GVM Series

Отзывы:

Carrier 38GVM Series, Руководство по обслуживанию, Страница: 30 / 70

Результаты поиска

Содержание 38GVM Series

Отзывы: