Carlton SP4012 Скачать руководство пользователя страница 53

Страница: 53 / 139

SP4012 TROUBLE SHOOTING GUIDE

COMPLAINT

CAUSE CORRECTION

Cutter wheel stops turning.

•

Belt not engaged.

•

Engine belt broke.

•

Poly chain

belt broke.

•

Sheared key in shaft.

•

Broke cutter wheel shaft.

•

Adjust yoke assembly.

•

Replace belt.

•

Replace belt.

•

Replace key.

•

Replace shaft.

Roar in machine when cutter
wheel is engaged.

•

Belt guards rubbing on
jackshaft or cutter wheel
shaft.

•

Jackshaft or cutter wheel
bearings going bad.

•

Re-position guards off of
shafts.

•

Replace bearings.

Traction loss of power.

•

Open free wheel valve.

•

Worn free wheel valve.

•

Relief valve set too low.

•

Hydraulic motor worn.

•

Close free wheel valve.

•

Replace free wheel valve.

•

Increase relief valve
pressure by turning relief
valve screw inward.

•

Replace Hydraulic motor.

Bearing will not take grease.

•

Grease fitting clogged.

•

Replace fitting

Cutter head swings faster one
way than the other.

•

Counter balance valve is
out of adjustment.

•

Adjust counter balance
valve to equalize swing
speed.

For all Radio Transmitter or Receiver problems, see the Radio Control Manual included at
the back of this manual.

Содержание SP4012












































































































































Результаты поиска

Содержание SP4012

Отзывы:

Похожие инструкции для SP4012

Бренды по названию

Популярные бренды

Carlton SP4012, Руководство пользователя

Результаты поиска

Содержание SP4012

Отзывы:

Похожие инструкции для SP4012

Бренды по названию

Популярные бренды