Carl Goldberg Products Ultimate 10-300 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 25

background image

9

30% Ultimate ARF

Take a straight pin and stick through

the blind nut inside the fuselage to
locate the holes for the struts.

Using the four 6-32x3/4” socket

head cap screws, mount the struts to
the top of the fuselage, short ones in
front longer ones in rear. Do not
tighten the screws down tight at this
time. Leave them loose until the top
wing is mounted.

Locate the two I-Struts and the eight

6-32x3/4” socket head cap screws.
The I-Struts are identified left and
right, top and bottom with small
stickers.

Fit the tabs on the top wing between

the brackets front and rear and
install a 6-32x3/4” socket head cap
screw through the holes. Do not
install nuts now.

«
...
7
8
9
10
11
...
»

Содержание Ultimate 10-300


























Отзывы:

Нет отзывов

Похожие инструкции для Ultimate 10-300

Бренд: Spin Master Страницы: 4

Бренд: Air Hogs Страницы: 6

Spitfire placards

Бренд: Eduard Страницы: 3

Бренд: E-FLITE Страницы: 19

Бренд: marklin Страницы: 24

Sd.Kfz.251/1 Ausf.B

Бренд: REVELL Страницы: 7

Бренд: Viessmann Страницы: 3

INTERACTIVE NODDY CAR

Бренд: LEXIBOOK Страницы: 33

Бренд: Tamiya Страницы: 24

BUILDING SITE DECORATION

Бренд: Faller Страницы: 4

Бренд: LeapFrog Страницы: 13

Tamagochi Friends

Бренд: Bandai Страницы: 4

Thunderbolt Mini A10

Бренд: J-Power Страницы: 31

Compessor with drive

Бренд: Faller Страницы: 4

Бренд: Fisher-Price Страницы: 10

Techno Gears Marble Mania Mine Shaft 2.0

Бренд: The Learning Journey Страницы: 72

Бренд: Eduard Страницы: 4

Бренд: Ravensburger Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды