background image

2

30% Ultimate ARF

WARNING! THIS IS NOT A TOY!

THIS IS NOT A BEGINNERS AIRPLANE

This R/C kit and the model you will build from it is not a toy!  It is capable of
serious bodily harm and property damage.  It is your responsibility, and yours
alone - to build this kit correctly, properly install all R/C components and
flying gear (engine, tank, radio, pushrods, etc.) and to test the model and fly
it only with experienced, competent help, using common sense and in accor-
dance with all safety standards as set forth in the Academy of Model
Aeronautics Safety Code.  It is suggested that you join the AMA and become
properly insured before attempting to fly this model.  If you are just starting
R/C modeling, consult your local hobby dealer or write to the Academy of
Model Aeronautics to find an experienced instructor in your area.
Write to:  Academy of Model Aeronautics, 5151 Memorial Dr. Muncie, IN
47302

LIMITED WARRANTY

Carl Goldberg Products is proud of the care and attention that goes into
the manufacture of parts for its model kits.  The company warrants that for
a period of 90 days, it will replace, at the buyers request, any part or materi-
al shown to the company's satisfaction to have been defective in workman-
ship or material at the time of purchase.
No other warranty of any kind, expressed or implied, is made with respect to
the merchandise sold by the company.  The buyer acknowledges and under-
stands that he is purchasing only a component kit from which the buyer will
himself construct a finished flying model airplane.  The company is neither
the manufacturer of such a flying model airplane, nor a seller of it.  The
buyer hereby assumes the risk and all liability for personal or property dam-
age or injury arising out of the buyers use of the components or the finished
flying model airplane, whenever any such damage or injury shall occur.
Any action brought forth against the company, based on the breach of the
contract of sale to the buyer, or on any alleged warranty there under, must
be brought within one year of the date of such sale, or there after be
barred.  This one-year limitation is imposed by agreement of the parties as per-
mitted by the laws of the state of Georgia.  

Important Information

Covering coming loose is Not COVERED UNDER WARRANTY. Due to tempera-
ture changes the plane may develop some wrinkles in the covering that you
will need to remove with an iron. Be sure to seal the edges down first so that
you do not cause the covering to shrink and leave exposed areas of wood.
Please inspect the plane before beginning to assemble to make sure you are
happy with it. After assembly has begun you cannot return the kit. If you find
a problem before beginning to assemble the plane you must contact us,
please do not return it to the dealer.

Содержание Ultimate 10-300


























Отзывы: