Carl Goldberg Products Ultimate 10-300 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

background image

21

30% Ultimate ARF

Place the tank between the holes

and use the two 14” tie wraps to
secure the tank to the mount.

Servo mounting

Locate the laser cut throttle servo

mount and the two 3/8” x1” bass
wood blocks. Epoxy the blocks to the
plate with the triangles underneath.

Epoxy the servo mount to the motor

box side in the proper position to line
up with your throttle arm. Put the E-Z
connector on the output arm of the
servo and connect the 2-56 push rod.

Locate the 2-56x10” throttle

pushrod and nylon snap link. Drill a
hole in the firewall in line with your
throttle arm and connect pushrod.

«
...
19
20
21
22
23
...
»

Содержание Ultimate 10-300


























Отзывы:

Нет отзывов

Похожие инструкции для Ultimate 10-300

Бренд: Trends UK Страницы: 3

Бренд: LEGO Страницы: 36

Deere CONSTRUCTION LOADER

Бренд: Peg-Perego Страницы: 52

Touch & Learn Activity Desk Deluxe

Бренд: VTech Страницы: 10

Бренд: AMATI Страницы: 56

Бренд: Idena Страницы: 3

Бренд: Kalee Страницы: 6

Spitfire F.Mk.22/24

Бренд: Eduard Страницы: 5

PREMIER E8 ABA DIESEL ENGINE

Бренд: M.T.H. Страницы: 24

Monkey Chase H8128

Бренд: Fisher-Price Страницы: 4

Бренд: Tabletop Scenics Страницы: 88

Бренд: Masterpiece Страницы: 8

Бренд: Fisher-Price Страницы: 10

Бренд: Rail King Страницы: 23

SPEED MASTER TG511

Бренд: THINK GIZMOS Страницы: 6

Бренд: Fisher-Price Страницы: 2

VisionAire AS3X

Бренд: PARKZONE Страницы: 20

Бренд: Blade Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды