Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 16

Страница: 16 / 378

1-6

General Setup and Operation

Alaris

System Directions for Use

PC Unit Section

Start-Up

(Continued)

If the Preventive Maintenance (

) Reminder option is

enabled and the PC Unit or an attached module is due for
preventive maintenance, a

MAINTENANCE REMINDER

message appears at power up.

Remove and, if needed, replace module requiring
maintenance with a new module (reference "Attaching
and Detaching Modules").

If "system" (PC Unit and attached modules) was powered
off to replace PC Unit, reinitiate start-up process.

If an "attached module" (such as, an Alaris

Pump

Module) was powered off and removed,

MAINTENANCE

REMINDER

display reflects removal of that module. To

continue start–up process, press

CONFIRM

soft key.

Responding to Maintenance Reminder

CONFIRM

MAINTENANCE REMINDER

Module(s) due for routine

preventive maintenance:

Module A: YYYY-MM-DD

NOTES:

If necessary, the reminder can be temporarily bypassed by
pressing the

CONFIRM

soft key.

Notify the appropriate facility personnel when a

MAINTENANCE REMINDER

occurs.

CONFIRM

MAINTENANCE REMINDER

Module(s) due for routine

preventive maintenance:

Adjusting Display Contrast

Press

DISPLAY CONTRST

soft key.

Midtown Hospital

Yes

NEW PATIENT ?

>Select Yes or No

“Yes” Clears Previous

Patient Data

DISPLAY

CONTRST

Содержание Alaris 8000 Series



























































































































































































































































































































































































Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды

Cardinal Health Alaris 8000 Series, Инструкция по применению

Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды