Instruction manual DI631
Instruction manual DI631
36
37
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
Tension adjustment
of the door spring
【
】
Figure5
Tension adjustment of the door spring
●
Connection of drain hoses
●
The
door
springs
are
set
at
the
factory
to
the
proper
tension
for
the
outer
door.
when the aesthetic door
panel
is
installed,
you
will
have
to
adjust
the
door
spring
tension.
Rotate
the
adjusting
screw
to
drive
the
adjuster
to
strain
or
relax
the
steel
cable
(see
figure
5).
Door
spring
tension
is
correct
when
the
door
remains
horizontal
in
the
fully
opened
position
，
yet
rises
to
a
close
with
the
slight
lift
of
a
finger.
21
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
A
Counter
Front
Drain pipe
NOTE
The top of the hose
must be less than
1000mm.
φ
40mm
B
T E N S I O N A D J U S T M E N T O F T H E D O O R S P R I N G
The door springs are set at the factory to the proper tension for the outer door. When the aesthetic
door panel is installed, you will have to adjust the door spring tension. Rotate the adjusting screw
to drive the adjuster to strain or relax the steel cable (see figure 5).
Door spring tension is correct when
the door remains horizontal in the
fully opened position, yet rises to a
close with the slight lift of a finger.
C O N N E C T I O N O F D R A I N H O S E S
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the
sink, making sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Tension adjustment
of the door spring
【
】
Figure5
Tension adjustment of the door spring
●
Connection of drain hoses
●
The
door
springs
are
set
at
the
factory
to
the
proper
tension
for
the
outer
door.
when the aesthetic door
panel
is
installed,
you
will
have
to
adjust
the
door
spring
tension.
Rotate
the
adjusting
screw
to
drive
the
adjuster
to
strain
or
relax
the
steel
cable
(see
figure
5).
Door
spring
tension
is
correct
when
the
door
remains
horizontal
in
the
fully
opened
position
，
yet
rises
to
a
close
with
the
slight
lift
of
a
finger.
21
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
A
Counter
Front
Drain pipe
NOTE
The top of the hose
must be less than
1000mm.
φ
40mm
B
Figure 5
Tension adjustment
of the door spring
D I S H WA S H E R I N S TA L L AT I O N S T E P S
1. Install the furniture door to the outer door of the dishwasher using the brackets provided.
Refer to the template for positioning of the brackets.
2. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to
your dishwasher. (2)
3. Connect the inlet hose to the cold water supply.
4. Connect the drain hose. Refer to diagram.(6)
5. Connect the power cord.
6. Affix the condensation strip under the work surface of cabinet. Please ensure the condensation
strip is flush with edge of work surface. (3)
7. Place the dishwasher into position.(4)
8. Level the dishwasher. The rear foot can be adjusted from the front of the dishwasher by turning
the Allen screw in the middle of the base of dishwasher use an Allen key (5A). To adjust the
front feet, use a flat screw driver and turn the front feet until the dishwasher is level (5B).
9. The dishwasher must be secured in place. There are two ways to do this:
»
Normal work surface: Put the installation hook into the slot of the side plane and secure it to
the work surface with the wood screws.(6)
»
Marble or granite work top: Fix the side with Screw. (7)
22
Dishwasher installation steps
●
1
Install
the
furniture
door
to
the
outer
door
of
the
dishwasher
using
the
brackets
provided.
Refer
to
the
template
for
positioning
of
the
brackets.
2
Adjust
the
tension
of
the
door
springs
by
using
an
Allen
key
turning
in
a
clockwise
motion
to
tighten
the
left
and
right
door
springs.
Failure
to
do
this
could
cause
damage
to
your
dishwasher(2).
3
Connect
the
inlet
hose
to
the
cold
water
supply
.
4
Connect
the
drain
hose.
Refer
to
diagram.(6)
5
Connect
the
power
cord.
6
Affix
the
condensation
strip
under
the
work
surface
of
cabinet.
Please
ensure
the
condensation
strip
is
flush
with
edge
of
work
surface.
(3)
7
Place
the
dishwasher
into
position.(4)
8
Level
the
dishwasher.
The
rear
foo
t
can
be
adjusted
from
the
front
of
the
dishwasher
by
turning
the
Allen
screw
in
the
middle
of
the
base
of
dishwasher
use
an
Allen
key
(5A).
To
adjust
the
front
feet,
use
a
flat
screw
driver
and
turn
the
front
feet
until
the
dishwasher
is
level
(5B).
9
The
dishwasher
must
be
secured
in
place.
There
are
two
ways
to
do
this:
A.
Normal
work
surface:Put
the
installation
hook
into
the
slot
of
the
side
plane
and
secure
it
to
the
work
surface
with
the
wood
screws
(
6).
B.
Marble
or
granite
work
top:Fix
the
side
with
Screw.
(7).
【Figure 7】
Figure 7
