Instruction manual DI631
Instruction manual DI631
26
27
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
N OT E :
EN 50242:
This programme is the test cycle. The information for comparability test in accordance with EN
50242, as follows:
»
Capacity: 12 settings
»
Position Upper basket: upper wheels on rails
»
Rinse Aid setting: 6
»
PI:0.49w;Po:0.45w
T U R N I N G O N T H E A P P L I A N C E
Starting a wash cycle:
»
Pull out the lower and upper baskets, load the dishes and push them back. It is recommended
to load the lower basket first, then the upper one (see the section entitled “Loading
the Dishwasher”).
»
Pour in the detergent (see the section entitled Salt, Detergent and Rinse Aid).
»
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification of
the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
»
Open the door, press the power button, and the On/Off light will turn on.
»
Press the program Button , the wash program will be changed as follows direction:
Intensive->Normal->ECO->90Min->Rapid;
C H A N G E T H E P R O G R A M M E
»
A cycle that is underway can only be modified if it has only been running for a short time.
Otherwise, the detergent may have already been released, and the appliance may have already
drained the wash water. If this is the case, the detergent dispenser must be refilled (see the
section entitled “Loading the Detergent“).
»
Open the door, press the Programme button for 3 seconds, the machine will be in standby
state, then you can change the programme to the desired cycle setting (see the section entitled
“Starting a wash cycle”).
N OT E :
If you open the door during a wash cycle, the machine will pause. The programme light will stop
blinking and the buzzer will sound every minute until you close the door. After you close the door,
the machine will continue working again.
F O R G OT TO A D D A D I S H
A forgotten dish can be added any time before the detergent cap opens:
»
Open the door a little.
»
After the spray arms stop working, you can open the door completely
»
Add forgotten dishes
»
Close the door
»
The dishwasher will start running again
AT T H E E N D O F T H E WA S H C Y C L E
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then
stop. Turn off the appliance using the ON/OFF button, shut off the water supply (if connected to
tap only) and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils
while they are still hot and more susceptible to breakage. They will also dry better.
S W I T C H O F F T H E D I S H WA S H E R
The programme light is on but is not blinking, only in this case the programme
has ended.
1.Open the door. Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap (if not plumbed into mains water supply).
O P E N T H E D O O R C A R E F U L LY
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15
minutes before removing from the appliance.
Open the dishwasher’s door, leave it ajar and wait a few minutes before removing the dishes. In
this way they will be cooler and the drying will be improved.
U N L OA D I N G T H E D I S H WA S H E R
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper
Basket onto the dishes in the lower one.
WA R N I N G :
It is dangerous to open the door during a wash cycle, because the hot water or steam may
scald you.
