CanyCom CM185 Скачать руководство пользователя страница 77

Страница: 77 / 98

Maintenance

-68-

Inspecting

5331M-0508-010E

New

Wear Limit

Blade Pin

Replace when either
of the part wears out

• Wear Limit
Blade: Up to line connecting outer edge and

inner edge.

Blade Pin: Up to either of the shoulder.

NOTE

1. Open cutting blade shield.
2. Visually inspect blades and pin for wear

and damage. If blades are worn normaly,
turn them over and use. Replace if both
edges are worn. If blades or pin are worn
excessively, deformed, damged, or missing,
replace them with new ones.

3. Inspect cutting rotor stay. If stay is worn

excessively, deformed or damged, contact
your CANYCOM representative and have it
replaced with new one.

4. Close blade sheild.

• Wear Limit: Up to the solid line in the

left figure (should have more than 15mm
clearance between edge of rotor stay and
mounting slot.)

NOTE

5332M-0508-020E

Blade

Rotating Direction

Flat Surfaces

Blade Pin

Wave Washer

Mounting, Dismounting Hole

Wear Area

Mounting Slot

Lug Hole

Rotor Stay

Wear Area

Handle with care.
These parts may become sharp

5332M-0508-040E

15mm

When New

Содержание CM185



































































































Результаты поиска

Содержание CM185

Отзывы:

CanyCom CM185, Руководство оператора, Страница: 77 / 98

Результаты поиска

Содержание CM185

Отзывы: