manualshive.com logo in svg

CanyCom CM185, Руководство оператора, Страница: 72 / 98

Поделиться
Скачать
CanyCom CM185 Скачать руководство пользователя страница 72

-63-

Maintenance

5

5335M-0507-030E

HST Oil Reservoir

1.  Park machine on level ground.
2.  Open engine hood.
3.  Visually inspect that oil level is between [MIN] 

and [MAX] lines on oil reservoir. If it is below 
[MIN], fill oil.

4.  Close engine hood.

Inspecting - Models without charge-pump

1.  Open engine hood.
2.  Remove cap on HST oil reservoir.
3.  Fill specified HST fluid into reservoir so that 

oil level is above [MIN] line on reservoir.

4.  Reinstall  cap  back  in  place  and  screw  it 

securely.

5.  Close engine hood.

Filling - Models without charge-pump

5335M-0507-050E

MIN

5.  Remove oil filter.
6.  Have a new oil filter. Apply thin coat of oil onto its oil seal and install it.

 •  HST system cannot be fully drained due to its design.
 •  Do not operate drive pedal or drive lever with HST oil drained. Doing so lets air into 

the circuit, necessitating to bleed the circuit.

NOTE

7.  Reinstall drain plug.
8.  Fill fresh oil to level.
9.  Reinstall filler cap.
10.  Start engine and run it for a while. Stop it and check HST oil level.
11.  Restart engine and drive machine back-and-forth from standstill several times.
12.  Check oil level. If it is lower, fill.
13.  Perform 10-12 until oil level stabilizes.
14.  Check if there is no oil leak.
15.  After changing HST oil, check oil level every 10-30 minutes of use for a while and fill as 

necessesary.

Содержание CM185



































































































Отзывы:

Нет отзывов