CanyCom CM185 Скачать руководство пользователя

Страница: 64 / 98

-55-

Maintenance

Engine

Engine Oil

•

To obtain correct reading, check oil level before starting, or wait about 10 minutes

after stopping engine to allow oil to drain back to oil pan.

•

Always check oil level on a level surface.

• Oil to use and capacity: Page 45.

NOTE

• Always stop engine and remove ignition key before servicing.

• An engine that has been running is very hot. Allow engine to cool before

servicing, or severe burns may result.

• Keep fire and spark away when servicing.

• Make certain to fill engine with correct grade of oil to the specified level.

Insufficient amount or wrong grade of oil reduces performance and may cause
permanent damage to engine.

• Dispose of the drained oil properly.

5332M-0506-010E

Oil Level Gauge

1.  Park machine on a level surface.
2.  Open engine hood.
3.  Pull out dipstick and wipe it clean.
4.  Insert dipstick fully and pull it out.

Inspecting

Содержание CM185



































































































Результаты поиска

Содержание CM185

Отзывы:

Похожие инструкции для CM185

Бренды по названию

Популярные бренды

CanyCom CM185, Руководство оператора

Результаты поиска

Содержание CM185

Отзывы:

Похожие инструкции для CM185

Бренды по названию

Популярные бренды