manualshive.com logo in svg

CanyCom CM185, Руководство оператора, Страница: 71 / 98

Поделиться
Скачать
CanyCom CM185 Скачать руководство пользователя страница 71

Maintenance

-62-

5

5335M-0507-010E

HST Oil Tank

Filler Cap

1.  Park machine on level ground.
2.  Open engine hood.
3.  Unscrew and remove filler cap. 

Inspecting - Models with charge-pump

Upper Limit

Lower Limit

5335M-0507-020E

Filler Cap

Dip Stick

1.  Open engine hood.
2.  Remove filler cap.
3.  Fill specified HST fluid into filler so that oil level is between upper and lower limits on 

dipstick.

4.  Reinstall filler cap back in place and screw it securely.
5.  Close engine hood.

Filling - Models with charge-pump

4.  Wipe dip stick with clean cloth. Reinstall filler 

cap and screw it fully.

5.  Unscrew and remove filler cap again. Visually 

inspect that oil level is between the upper 
and lower limits on dip stick. If it is below the 
lower limit, fill oil.

6.  Reinstall filler cap and screw it fully.
7.  Close engine hood.

1.  Open engine hood.
2.  Have an appropriate oil drain pan.
3.  Remove filler cap.
4.  Remove drain plug to drain oil tank.

Changing - Models with charge-pump

 •  HST system cannot be fully drained due to 

its design.

 •  Do not operate drive pedal or drive lever 

with  HST  oil  drained.  Doing  so  lets  air 
into the circuit, necessitating to bleed the 
circuit.

NOTE

Adjust Nut

Lock Nut

5347M-0507-070E

Содержание CM185



































































































Отзывы:

Нет отзывов