manualshive.com logo in svg

Canon PIXMA MX7600, Руководство по обслуживанию

Поделиться
Скачать
Canon PIXMA MX7600 Скачать руководство пользователя страница 61

<#1 BIT SWITCH>

 

1.

In the #1 BIT SWITCH menu, the following screen is displayed: 

 

2.

Each time the up or down cursor button (or the OK button) is pressed, the SW# changes from 01 to 20. 

Be cautious not to select the SW numbers which are not used in servicing.  

The SW numbers used in servicing:  SW# 01, 02, 03, 04, 05, 06, 07, 10, 11, 13 

The SW numbers not used in servicing (as of December 2007):  SW# 08, 09, 12, 14 to 20  

3.

Each SW# has 8-bit information. Using the left or right cursor buttons, move the cursor to the bit to be changed, and enter 

the setting value (1 or 0). 

Bit 7 -> 00000000 <- Bit 0  

4.

Press the OK button to finalize the setting value. For the definition and description of each bit of each SW#, refer to the "

 

G3 Facsimile Service Data Service Handbook

." 

English: QY8-13BC-010 

Japanese: QY8-12B6-020  

5.

Press the Stop/Reset button to save the setting value.  

6.

Press the ON/OFF button.  

 

PTT PRAMETER 
#1 BIT SWITCH 
SW#01  00000000 

59 / 65

Содержание PIXMA MX7600




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды