Canon PIXMA MX7600 Скачать руководство пользователя страница 4

Страница: 4 / 67

*1: The ink absorber and wetting liquid unit should be replaced at the same time.

(2) Periodic maintenance

No periodic maintenance is necessary.

(3) Periodic replacement parts

There are no parts in this machine that require periodic replacement by a service engineer.

(4) Replacement consumables

There are no consumables that require replacement by a service engineer.

mode.

LF / Eject
correction

- At logic board replacement
- At feed roller ass'y

replacement

To correct line feeding (LF
roller diameter).

None.
Perform in the service
mode.

5 min.
(LF
correction
and Eject
correction
is
performed
at the same
time.)

- At logic board replacement
- At platen unit replacement

To correct line feeding (eject
roller diameter).

None.
Perform in the service
mode.

LAN resetting

- At protection sheet

replacement

To initialize the network setting. None.

Perform in the user
mode.
- Machine buttons
- Computer (IJ Network

tool)

1 min.

LAN setting
information
display

- At confirmation of the

network setting (as needed)

To confirm the network setting.

None.
Perform in the user
mode.
- Machine buttons
- Computer (IJ Network

tool)

1 min.

- DO NOT loosen the red screws at both ends of the carriage shaft, securing the print head position, as they

are not re-adjustable.

- The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor

unit.

2 / 65

Содержание PIXMA MX7600




































































Результаты поиска

Содержание PIXMA MX7600

Отзывы:

Бренды по названию

Популярные бренды

Canon PIXMA MX7600, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA MX7600

Отзывы:

Бренды по названию

Популярные бренды