Canon PIXMA MX7600 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 67

Canon PIXMA MX7600 Скачать руководство пользователя страница 1

MX7600
Service Manual

Revision 0

QY8-13BU-000

COPYRIGHTc2008 CANON INC. CANON MX7600 032008 XX 0.00-0

Scope

This manual has been issued by Canon Inc., to provide the service technicians of this product with the information necessary for
qualified persons to learn technical theory, installation, maintenance, and repair of products. The manual covers information
applicable in all regions where the product is sold. For this reason, it may contain information that is not applicable to your
region.

This manual does not provide sufficient information for disassembly and reassembly procedures.
Refer to the graphics in the separate Parts Catalog.

Revision

This manual could include technical inaccuracies or typographical errors due to improvements or changes made to the product.
When changes are made to the contents of the manual, Canon will release technical information when necessary. When
substantial changes are made to the contents of the manual, Canon will issue a revised edition.

The following do not apply if they do not conform to the laws and regulations of the region where the manual or product is used:

Trademarks

Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders.

Copyright

All rights reserved. No parts of this manual may be reproduced in any form or by any means or translated into another language
without the written permission of Canon Inc., except in the case of internal business use.

Copyright © 2008 by Canon Inc.
CANON INC.
Inkjet Device Quality Assurance Div. 2
451, Tsukagoshi 3-chome, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8530, Japan

1
2
3
...
»

Содержание PIXMA MX7600




































































Отзывы:

Нет отзывов