Canon PIXMA MP640 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 57

Canon PIXMA MP640 Скачать руководство пользователя страница 17

2-3. Troubleshooting by Symptom

Symptom

Solution

Faulty operation

The power does not turn on.
The power turns off immediately
after power-on.

(1) Confirm connection of the power supply unit:

- Harness and connector conditions

(2) Replace the following item(s):

- Logic board
- Power supply unit
- Panel board

A strange noise occurs.

(1) Examine and remove any foreign material or paper debris.
(2) Replace the following item(s):

- The part generating the strange noise
- Logic board

The LCD does not display properly.
A portion of the LCD is not
displayed.
The display flickers.

(1) Confirm cable connection (LCD FFC and panel harness):

- Harness and connector conditions
- No cable breakage, etc.

(2) Replace the following item(s):

- LCD FFC
- LCD viewer unit
- Panel board
- Logic board

Paper feed problems (multi-feeding,
skewed feeding, no feeding).

(1) Examine and remove any foreign material or paper debris.
(2) Confirm that the paper guides are set properly.
(3) Confirm the PF rear cover and the cassette conditions.
(4) Confirm cable connection.
(5) Replace the following item(s):

- ASF unit (for paper feeding error from the rear tray)
- PF pick-up unit (for paper feeding error from the cassette)
- PE sensor board
- Pressure roller unit
- Cassette unit

Faulty scanning (no scanning,
strange noise).

(1) Confirm cable connection (scanner motor cable and CIS

FFC):

- Harness and connector conditions
- No cable breakage, etc.

(2) Replace the following item(s):

- Scanner unit
- Logic board

The CD / DVD tray is not pulled in
the feeder.

(1) Confirm the reflector of the back of the CD / DVD tray:

- Cleaning of the reflector

(2) Replace the following item(s):

- Logic board
- CD-R tray
- Platen unit

Unsatisfactory print quality No printing, or no color ejected.

Faint printing, or white lines on
printouts.
Uneven printing.
Improper color hue.

(1) Confirm the ink tank conditions:

- Confirmation of the air-through of an ink tank
- Re-setting of an ink tank
- Whether the ink tank is Canon-genuine one or not
- Whether the ink tank is refilled one or not

(2) Remove foreign material from the purge unit caps, if any.
(3) Perform cleaning or deep cleaning of the print head.
(4) Perform print head alignment.
(5) Replace the following item(s):

- Print head

*1

, and ink tanks

- Logic board
- Purge drive system unit

Paper gets smeared.

(1) Clean the inside of the machine.
(2) Perform bottom plate cleaning.

14 / 54

«
...
15
16
17
18
19
...
»

Содержание PIXMA MP640


























































Отзывы:

Нет отзывов