manualshive.com logo in svg

Canon NP6251, Сервисный бюллетень

Поделиться
Скачать
Canon NP6251 Скачать руководство пользователя страница 42

6251-015

- 

2 / 3 -

Servicing

: When the aforementioned problem occurs, or when problem is anticipated with certain machines,

replace both the inner cover (left) and the air filters with the new parts.  (See Fig. 1)

Precautions to take in installing the air filter 

U 

(FF5-7572) to the inner cover (left) (FF5-7571) are

listed below.

1. 

 

Position the air filter U in such a way that the filter can be attached on the top and the rim of the
filter is positioned toward you. (See Fig. 1)

2. 

 

The farther end of the air filter U and the section provided with the rim is to be inserted to the slot
of the inner cover shown shaded in View A.

Air Filter

Air Filter U

*2

(FF5-7572)

Air Filter

(FB4-6224)

Air Filter (Electrostatic)
(FB4-6225)

Inner Cover (Left)
(FF5-7571)

New

Old

Fig. 1   Old and New parts

Section of View A

View A

Rim

*1.

 

Inner cover (left) includes an air
filter.

*2.

 

Air filter U includes an air filter
and electrostatic air filter.

Inner Cover (Left)

*1

Содержание NP6251




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды