manualshive.com logo in svg

Canon NP6251, Сервисный бюллетень

Поделиться
Скачать
Canon NP6251 Скачать руководство пользователя страница 18

6251-006 Rev. 2

- 

3 / 6 -

No.

Item

Description

9

Complying with Energy

Star Tire2

(Contd.)

So that models not designed for Energy Start Tire2 may also use the
updated ROM (Ver. 7), a DIP SW has been added to the DC controller
PCB to enable selection of Energy Star Tire2 compliance or non-
compliance. (See the diagram below.)
For this reason, it is important to find out whether or not the model is
designed for Energy Start Tire2 before replacing the DC controller PCB.
The use of an updated ROM on a DC controller PCB of previous version
will not update the machine to accommodate Energy Star Tire2.

DC Controller PCB Available as a Temporary Measure

•

 

A DIP switch (DIPSW 102) consisting of two circuits has been added to
the existing DC controller PCB.

•

 

Compliance/Non-Compliance with Energy Star Tire2

Note that bit 2 is not used.

ON

1   2

SW102

DC Controller PCB (for temporary use)

DC Controller PCB Available as a Permanent Measure

•

 

The change made provides four circuits instead of three for a DIP switch
(DIPSW101) on the DC Controller PCB.

•

 

Allows selection of compliance or non-compliance with Energy Star
Tire2.

Note that bits 1 through 3 possess their previous functions, and are set
to suit the site of installation.

ON

1  2   3   4

SW101

DC Controller PCB (for permanent use)

Bit 4 on SW101

Energy Star Tire2

ON

Selects compliance

OFF

Selects non-compliance

Bit 1 of SW102

Energy Star Tire2

ON

Selects compliance

OFF

Selects non-compliance

Содержание NP6251




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды