manualshive.com logo in svg

Canon NP6251, Сервисный бюллетень

Поделиться
Скачать
Canon NP6251 Скачать руководство пользователя страница 29

6251-010

- 

2 / 3 -

Servicing : If a protective sheet is not found in the upper left stay of the machine (i.e., if the machine's copyboard

glass is 4 mm in thickness), be sure to attach the protective sheet (FY1-1174) prepared for the field as
indicated in Figure 2.
The field use protective sheet (FY1-1174) is intended as a one-time measure, and will not be assigned
as a service part. In the near future, be sure to use the new protective sheet (FB4-9953; see Figure 1 for
its location).
If you have removed the control panel of  a machine which was provided with a field use protective
sheet, make sure that the field use protective sheet is under the control panel.

Attaching the Field Use Protective Sheet
1.

 

Remove the vertical size plate and the left stay cover.

2.

 

Insert the protective sheet between the upper left stay and the control panel, and attach it to the
upper left stay according to the reference points indicated in Figure 2.

3.

 

Mount the left stay cover and the vertical size plate.

Figure 2 Location of the Field Use Protective Sheet

Reference points
for attachment

Left tray cover

Vertical size plate

Spacer

Upper left stay

A gap is found here.

Protective sheet (double-
sided adhesive tape where
shaded)

Содержание NP6251




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды