Canon iPF6100 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя страница 339

Страница: 339 / 367

Chapter 8

8-6

Cannot print
as specified.

Press Load/Eject
and replace roll
with 10 in. wide or
larger roll.

03010000-2E1F

Undersized paper loaded for
internal printing (roll media)

Replace with roll media at least
10 inches in width.

Cannot print
as specified.

Press Load/Eject
and replace paper
with A2/
16.6"x23.4"
(vertical) or larger

03010000-2E1F

The first sheet used for adjustment
printing or the like was A2 or
larger-sized but the second sheet
used was smaller than A2.

Prepare about 10 sheets of A2 or
larger-sized paper.
Replace with A2 or any larger-
sized paper.

Cannot feed paper.

Remove paper and
press Load/Eject.

03010000-2E25

Feeding error

Remove the paper jam and
reload the paper.

Cannot detect papr

Remove paper and
press Load/Eject.

03010000-2E25

Paper jam while feeding/ejecting/
printing

Remove the paper jam and
reload the paper.

Cannot load.

Press Load/Eject
and reload the
paper.

03010000-2E27

Paper jam during feeding/printing/
ejection

Reload the paper.

This paper
cannot be used.
Check supported
paper sizes.

Load/Eject:
Change Paper

03010000-200E

Undersized paper (cut sheets/roll
media)

Replace with larger-sized paper.

This paper
cannot be used.
Check supported
paper sizes.

Load/Eject:
Change Paper

03010000-200F

Oversized paper (cut sheets/roll
media)

Replace with smaller-sized
paper.

Display massage

Code*

Condition detected

Action

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды