Canon iPF6100 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя страница 228

Страница: 228 / 367

Chapter 4

4-56

4.3.15 PCBs

0012-6407

Do not replace the main controller PCB and maintenance cartridge relay PCB(ROM board) at the same time.

These PCBs store important data such as settings and carriage drive time. Before replacement of enther PCB,

the data stored in it is move to the other PCB through internal communication so that it can be taken over to the

new PCB automatically. This is the reason whey the two PCBs should not be replaced at the same time.

If you want to replace both PCBs at the same time, first carry out the procedure "a" and then carry out the

procedure "b".

After replacing whth the maintemance controller PCB or maintenance cartridge relay PCB which are supplied

as service parts, check that the firmware to the latest version.

a) Removing the main controller PCB

1) To remove the main controller PCB, open the top cover and remove the roll feed unit, left circle cover, tank

cover, left cover, lower rear cover, lower rear left cover and left rear cover.

See DISASSEMBLY/REASSEMBLY > Points to note on Disassembly and Reassembly > External Covers.

2) Remove all connectors from the main controller PCB.

3) Remove two coin screws[1], interface cover[2] and screw[3] in this order.

F-4-98

[1]

[2]

[3]

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды