Canon iPF6100 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя страница 144

Страница: 144 / 367

Chapter 2

2-66

2.5.3 Carriage system

0016-8206

F-2-50

Multi sensor

The photo-reflection-type multi sensor is composed of four LEDs (red, blue, green and infrared) and two light-

sensitive sensors. It detects the leading edge, skewing, and width of media and is used for adjustment of the

registration, head height, and color calibration.

During head adjustment, the light reflected by the infrared LED and green LED is detected by two light-sensitive

sensors to calculate the head height from the difference between the measurements.

When color calibration is executed, a color chart printed is read with three-color LED (red, blue, green), so color

correction is implemented on the basis of the readings.

Ink mist adhering to the sensor could deliver incorrect measurement readings when color calibration is executed.

If the ink dot count exceeds a tolerance, the service error (E194-4034) would occur. If it does, execute service

mode: SERVICE MODE > ADJUST > GAP CALIB. after the multisensor has been replaced to clear the dot

count.

Lift cam sensor

Linear encoder sensor

Multi sensor

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание iPF6100 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF6100 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды