background image

Canoga Perkins Corporation, 20600 Prairie Street, Chatsworth, CA 91311-6008 

Phone: (818) 718-6300, FAX (818) 718-6312 www.canoga.com 

P/N 6943465 Rev A  

 

Page 4 of 7

 

 

 

Bits per second: 38400bps 

 

Data bits: 8 

 

Parity: None 

 

Stop bits: 1 

 

Flow control: None 

 

Terminal emulation: VT100 

 
If the HyperTerminal screen is scrolling up, make sure that “Terminal Emulation” in the 
Properties menu is set to VT100.  If the screen shows random symbols instead of letters, verify 
that the terminal speed is set to 38400bps.   
 
In the log-in screen, type the default Login “

manager

” and the Password “

manager

” to access the 

user interface.  The MAIN MENU will appear and will allow you to make necessary 
configuration changes based on your selection.   

 
CANOGA PERKINS CORP. 
20600 Prairie Street 
Chatsworth, CA 91311 
Tel: 818 718 6300 
E-mail: [email protected] 
Web: www.canoga.com 
 
HS8000 Hardened Ethernet Switch Version 1.2 
 
     Login: manager 
     Password: ******* 
 

Figure 5.  Log In screen 

 

CANOGA PERKINS CORP. 
20600 Prairie Street 
Chatsworth, CA 91311 
Tel: 818 718 6300 
E-mail: [email protected] 
Web: www.canoga.com 
 
HS8000 Hardened Ethernet Switch Version 1.2 
 
Main Menu 
 
        1. System Configuration 
        2. Port Menu 
        3. Switch Configuration 
        4. Access Control 
        5. IP Parameters Configuration 
        6. Event Log 
        7. Log Out 
        0. Close Connection 
 
     Enter Selection by number:  

Figure 6.  Main Menu screen 

 

Содержание HS8000








Отзывы: