background image

26

NOTES

Warranty

Don’t risk your appliance warranty

Only a licensed person will give you a Compliance Certificate,
showing that the work complies with all the relevant standards.

And only a licensed person will have insurance protecting their
workmanship for 6 years.

So make sure you use a licensed person to install this appliance
and ask for your Compliance Certificate to ensure the manufac-
turers appliance warranty will be honoured.

Distributor

This appliance is designed, manufactured and distributed by:

Tel: 1300 727 421

3

The  benefit  conferred  by  this  warranty  are  in  addition  to  all  other  rights  and 
remedies  in  respect  of  the  product  that  consumers  have  under  the  Trade 
Practices Act  and  similar  laws  of  the  States  and  Territories. 

We  warrant  this  Cannon  appliance  to  be  free  of  defects  in  materials, 
workmanship  and  manufacturing  to  the  original  purchaser  for  2  years,  (10  years 
on  the  heat  exchanger)  from  the  date  of  original  purchase.  We  will,  at  our 
option  and  subject  to  the  terms  of  this  warranty,  repair  or  replace  free  of  charge 
this  Cannon  appliance  or  any  component  part,  which  upon  examination  by  us 
or  our  repair  agent  is  found  to  be  defective  in  materials,  workmanship  or 
manufacturing.  However,  this  warranty  does  not  cover  any  consumables  (if  any). 
The  purchaser  must  present  the  original  purchase  receipt  to  us  when  making 

any  claim  under  this  warranty.

This  warranty  will  not  apply  if:  (i)  a  compliance  label  or  serial  number  (as  the 
case  may  be)  has  been  removed  from  the  appliance  or  rendered  illegible;  (ii) 
the  appliance  has  been  subject  to  misuse,  abuse,  accident,  incorrect  installation 
or  non-domestic  use;  (iii)  the  appliance  has  been  modified,  tampered  with  or 
repaired  by  a  person  other  than  our  authorised  repair  agent;  (iv)  the  appliance 
is  re-installed/relocated  during  the  warranty  period.

The  purchaser  is  responsible  for  all  travelling  expenses  if  the  purchaser 
requests  any  repair  be  carried  out  at  a  place  outside  areas  normally  serviced 
by  our  repair  agents.
Should  you  require  service  on  this  appliance,  please  contact  our  service 
department  on  1300  727  421.

Enter  the  details  of  the  date  installed  and  the  Compliance  Certificate  number  in 
the  appropriate  area  on  the  rear  page  of  this  manual.

Содержание Fitzroy Inbuilt















Отзывы: