background image

28

 

 

www.cannondownriggers.com 

Fishing With Your Downrigger 

 

After programming your Digi-Troll, release some line 

from your rod and reel so that the lure is anywhere from 
5 to 100 feet behind the boat. This is called drop back. 
Attach the fishing line firmly into the line release. Press 
and hold the down key to lower the weight to the desired 
depth as indicated on the display or select a pre-
programmed weight depth. Place the fishing rod in the 
rod holder and reel up the slack so that your rod has a 
slight bend in it. When a fish strikes the lure, the line will 
separate from the release. Then you will be free to fight 
the fish and bring it in on your rod and reel. 

 

Manual Descent 
 

By turning the clutch knob gently clockwise (toward 

the boom), you can let your trolling weight descend as 
fast or as slowly as you wish. Turning the knob counter-
clockwise (away from the boom) stops the weight. This 
gives you control to let it plunge rapidly or sink slowly to 
a predetermined trolling depth. With multiple downrig-
gers, you could start all your weights creeping down, 
one at a time, and then stop them each in turn. 

 

Note: In order to track line out, the Digi-Troll must 
be turned on. 
 
WARNING—DO NOT TOUCH THE CABLE REEL 
WHILE THE DOWNRIGGER IS IN USE! 
 

The Positive Ion Control System 

 

Your boat has an electrical charge around the hull in 

water. If a boat is properly grounded and has a proper 
zinc anode, that charge should be slightly positive when 
measured from ground to the downrigger cable. Positive 
Ion Control (PIC) is the use of electricity to control that 
charge and its fluctuation so that it is always maintained 
at a specified set voltage. 
 

The practice of setting up and maintaining a slight 

positive charge on fishing gear has been used by com-
mercial fishermen for many years. This practice has en-
abled some fisherman to increase yield when used 
along with other good fishing and boating practices. 
 

Cannon's electric downriggers offer fishermen a big 

advantage in being able to stabilize and control the posi-
tive charge around their boat. Because of the composite 
construction of the frame, Cannon downriggers are insu-
lated from your boat's hull charge.  
 

When the stainless steel downrigger cable is low-

ered into the water, the natural ionization between the 
cable and the boat creates a positive charge of 0.7 to 
0.9 volts in saltwater and 0.3 to 0.6 volts in fresh water. 
This natural voltage is dependent upon salinity and min-
eral content of the water. Your actual voltage may vary. 

F

ishin

g T

heor

Cable Terminator 

Weight Insulator 

The Short Stop System  

 

The Short Stop system is composed of three critical 

components: the electronic unit, the reel conductive 
path, and the trolling weight insulator. 
 

While the downrigger cable is in the water, there is a 

minute electrical current that flows between the cable 
and the grounded metal boat components in the water. 
When the cable clears the water, this current flow will 
stop. The Short Stop system senses this interruption 
and turns off the motor. The trolling weight insulator is 
used to break the cable contact to the water while the 
weight is still in the water. The reel conductive path al-
lows the circuit path to be made through the structure of 
the downrigger. 

NOTICE:  Short stop and Positive Ion 
Control features do not function when 
spooled with monofilament or super 
lines. 

Содержание DIGI-TROLL 10









































Отзывы: