Cannon CANTERBURY Скачать руководство пользователя

Страница: 6 / 20

6 | Cannon Fitzroy / Canterbury Inbuilt

inbuilt: fitzroy sPeCifiCations

gas type

natural or Propane gas,
as indicated on data label

gas consumption

26.0 MJ/hr

energy output

5.98 kW / 21.45 MJ/hr

energy star rating

4.05 stars

Heater type

gas space heater approved
to aS 4553:2008

Operating pressure
(at burner high setting)

natural gas 0.75 kPa
Propane gas 2.65 kPa

gas regulator

Integral part of controller

Min. inlet pressure

1.13 kPa (ng)
2.75 kPa (Propane)

Fan

3 speed

Ignition

electronic direct spark

Power requirement

240 vaC 10 amp

Power consumption

90 va maximum

Minimum cavity
dimensions

Height 605 mm*
Width 700 mm*
Depth 405 mm*

Optional accessories

• Glass front

• Remote thermostat

• Spacer kit

• 3 sided surround

• 4 sided surround

• Console kit

Overall dimensions

refer to

FIG 3

*For installation into a non-combustible fireplace, ie:
masonry or brick

Please note:

• When installing into a mock fireplace a mock

fireplace installation kit must be used.

• The data label is located in the fan chamber. Access

by removing fascia.

Cannon fitzroy inbuilt

fig 3 front View and side View

808 mm

50 mm 347 mm

8 mm

Содержание CANTERBURY





















Результаты поиска

Содержание CANTERBURY

Отзывы:

Похожие инструкции для CANTERBURY

Бренды по названию

Популярные бренды

Cannon CANTERBURY, Инструкция по эксплуатации

Результаты поиска

Содержание CANTERBURY

Отзывы:

Похожие инструкции для CANTERBURY

Бренды по названию

Популярные бренды