Canature WaterGroup 89UF Скачать руководство пользователя страница 3

Страница: 3 / 36

SAFETY

Throughout this manual, certain conventions are used, including;

HAZARD SYMBOLS

For your own safety, please pay strict attention! Examples include: temperature, electrical, water

pressure, etc.

HAZARD SIGNALS

DANGER

Indicates a hazardous situation that, if not avoided will result in death or serious injury,

and/or property loss or damage.

WARNING

Indicates a hazardous situation that, if not avoided may result in death or serious injury,

and/or property loss or damage.

CAUTION

Indicates a hazardous situation that, if not avoided, could result in a minor or moderate injury, and/or

property loss or damage

NOTICE

Indicates important information, that if not followed may result in damage to equipment, or property

loss.

WARRANTY EXCLUSIONS

Identify specific instructions that, if not followed, will void the warranty. The warranty provided gives

you specific legal rights and otherwise limits your legal rights to the extent permitted by law. By

installing and/or using this product, you are accepting these limits on your legal rights.

NOTES

NOTE

Help you take full advantage of the system and are used to emphasize installation, operation, or

maintenance information that is important but does not present a hazard.

MANDATORY SIGNS

Used to depict a specific behavior that MUST be followed to avoid the present hazard (problem).

Canature WaterGroup™

Canature WaterGroup U.S.A. Inc. / Canature WaterGroup Canada Inc. (“Canature”) has disclosed all known risks associated with the

product within this manual but cannot disclose risks that are beyond its knowledge.
Original instructions. All information, illustrations, and specifications in this manual are based on the latest information available

at the time of the publication.
The right is reserved to make changes at any time without notice.

Содержание 89UF





































Результаты поиска

Содержание 89UF

Отзывы:

Похожие инструкции для 89UF

Бренды по названию

Популярные бренды

Canature WaterGroup 89UF, Руководство пользователя

Результаты поиска

Содержание 89UF

Отзывы:

Похожие инструкции для 89UF

Бренды по названию

Популярные бренды