background image

  | 

12 

EN-Rev IM/GN-AM-EN/2.9 Copyright © March, 2022. CSI Solar Co., Ltd.

 

www.csisolar.com

 

 

The  grounding  method  described  below  is 
recommended by Canadian Solar. 

 

GROUNDING METHOD: BOLT + TOOTHED NUT + CUP WASHER. 

 

 

A grounding kit containing an M5 (3/16") SS cap bolt, an 
M5 (3/16") SS flat washer, an M5 (3/16") SS cup washer, 
and an M5 (3/16") SS nut (with teeth) is used to attach 
copper grounding wire to a pre-drilled grounding hole 
on the frame (see image above).   

 

Place  the  wire  between  the  flat  washer  and  the  cup 
washer.  Ensure  that  the  cup  washer  is  positioned 
between the frame and the wire with the concave side 
up  to  prevent  galvanic  corrosion.  Tighten  the  bolt 
securely  using  the  SS  toothed  nut.  A  wrench  may  be 
used to do this. The tightening torque is 3-7 Nm (2.2-5.2 
ft-lbs). 

6.0 MOUNTING INSTRUCTIONS 

The applicable regulations pertaining to work 
safety, accident prevention and securing the 
construction site must be observed. Workers 

and third party personnel shall wear or install fall arrest 
equipment. Any third party need to be protected against 
injuries and damages. 

 

The mounting design must be certified by a registered 
professional  engineer.  The  mounting  design  and 
procedures must comply with all applicable local codes 
and requirements from all relevant authorities. 

 

The module is considered to be in compliance with UL 
61730 and IEC 61215 only when the module is mounted 
in the manner specified by the mounting instructions 
included in this installation manual. 

 

The system designer and installer are responsible for 
load  calculations  and  for  proper  design  of  support 
structure. 

 

Any  module  without  a  frame  (laminate)  shall  not  be 
considered  to  comply  with  the  requirements  of  UL 
61730  unless  the  module  is  mounted  with  hardware 
that  has  been  tested  and  evaluated  with  the  module 
under this standard or by a field Inspection certifying 
that  the  installed  module  complies  with  the 
requirements of UL 61730. 

 

Canadian Solar does not provide mounting hardware. 

 

Standard  modules  can  be  mounted  onto  a  support 
structure  using  one  of  several  approved  methods  as 
described  below.  For  information  about  other 
installation  methods,  please  contact  your  local 
representative. Failure to use a recognized installation 
method will void the Canadian Solar warranty. 

 

Use  appropriate  corrosion-proof  fastening  materials. 
All  mounting  hardware  (bolts,  spring  washers,  flat 
washers, nuts) should be hot dip galvanized or stainless 
steel. 

 

Use a torque wrench for installation.   

 

Do  not  drill  additional  holes  or  modify  the  module 
frame. Doing so will void the warranty.   

 

Standard modules can be installed in either landscape 
or  portrait  orientations.  Refer  to  the  detailed 
instructions  for  further  guidance.  Please  note  that  in 
areas  with  heavy  snowfall  (>  2400  Pa)  further 
countermeasures  such  the  use  of  additional  support 
bars  should  be  considered  to  avoid  snow  loads 
damaging the lowest row of modules. 

 

In  cases  where  an  additional  support  bar  is 

To  fix  the  wire  between  the 

flat  washer  and  cup  washer, 

place  the  cup  washer 

(concave  side  up)  between 

the frame and the wire. 

Then  tighten  the  bolt 
using the toothed nut. 

Содержание CS1V-MS












































Отзывы: