background image

  | 

EN-Rev IM/GN-AM-EN/2.9 Copyright © March, 2022. CSI Solar Co., Ltd.

 

www.csisolar.com

 

environment to avoid direct sunlight  and  moisture. If 
modules  are  stored  in  an  uncontrolled  environment, 
the  storage  time  should  be  less  than  3  months  and 
extra  precautions  should  be  taken  to  prevent 
connectors from being exposed to moisture or sunlight, 
like using connector endcaps. In any circumstance, for 
pallets of modules packaged in landscape orientation, 
stacking  of  no  more  than  two  layers  is  allowed,  for 
pallets  of  modules  packaged  in  portrait  orientation, 
stacking is not allowed. 

 

When unloading modules pallets from flat truck, please 
use a crane or a forklift to remove the module pallets. 
When  unloading  modules  pallets  from  containers, 
please use a forklift to remove the module pallets from 
the container or trailer. Do not move any pallets within 
the 

container or trailer without properly lifting them 

first.

 The forklift should be close to the ground in order 

to avoid the top of module pallets touching the top of 
the cabinet door. The thickness of forklift teeth should 
be less than 75mm, and the length of the forklift teeth 
should be longer than 2300mm, when unloading 6W-
MS module pallets from the short side. For unloading 
CS7N-MS  and  CS7L-MS  modules,  the  thickness  of 
forklift teeth should be less than 75mm, the length of 
the forklift teeth  should  be longer than 1250mm and 
the width of forklift teeth should be wider than 600mm 
(from  middle  to  middle  of  the  forklift  teeth).  Consult 
your Canadian Solar representative for more detailed 
unloading instructions.

 

 

Unpack  module  pallets  carefully,  following  the  steps 
shown on the pallet. Unpack, transport and store the 
modules with care. 

 

Modules must always be unpacked and installed by two 
or three people. Always use both hands when handling 
modules. 

 

For modules vertically packed lying on the 
short  side  (CS7L  and  CS7N),  it  is 
recommended  to  support  the  unpacked 

modules  by  one  person  during  the  unpacking  process. 
Please use an anti-tipping structure that can be built with 
the  pallet’s  own  wooden  frame  according  to  the 
instructions below:

 

 

 

During  unpacking,  the  unpacked  modules  should  be 
properly fixed. After unpacking, it is recommended to 
place  the  remaining  modules  in  the  pallet  shall  be 
placed horizontally on a pallet not exceeding the total 
number 12 of in one stack. Visit our website or contact 
your Canadian Solar representative for more detailed 
unpacking requirements.

 

 

 

Do not

 lift modules by their wires or junction box, lift 

them by the frame. 

 

Do not

 allow the panels to sag or bow under their own 

weight when being carried. 

 

Stacks  of  modules  should  contain  no  more  than  12 
modules, and the frames should be aligned. 

 

Do not

 place excessive loads on the module or twist the 

module frame.   

 

Do  not

  stand,  step,  walk  and/or  jump  on  modules 

under  any  circumstances.  Localized  heavy  loads  may 
cause  severe  micro-cracks  at  cell  level,  which  in  turn 
may compromise module reliability and void Canadian 

Anti-

tipping 

system 

Содержание CS1V-MS












































Отзывы: