Campbell MetSENS Series Скачать руководство пользователя страница 29

Страница: 29 / 39

Table B-1: Campbell Scientific sensor SDI-12 command and response sets

Name

Command

Response

Address query

a<CR><LF>

Change address

aAb!

b<CR><LF>

Start measurement

aM!

aM1!...aM9!

atttn<CR><LF>

Start measurement

and request CRC

aMC!

aMC1!...aMC9!

atttn <CR><LF>

Start concurrent measurement

aC!

aC1!...aC9!

atttnn<CR><LF>

Start concurrent measurement

and request CRC

aCC!

aCC1!...aCC9!

atttnn<CR><LF>

Send data

aD0!...aD9!

a<values><CR><LF> or

a<values><CRC><CR><LF>

Continuous measurement

aR0!...aR9!

a<values><CR><LF>

Continuous measurement

and request CRC

aRC0!...aRC9!

a<values><CRC><CR><LF>

Information on each of these commands is given in the following sections.

B.1.1 Acknowledge active command (a!)

The acknowledge active command (

) is used to test a sensor on the SDI-12 bus. An active

sensor responds with its address.

B.1.2 Send identification command (al!)

Sensor identifiers are requested by issuing command

aI!

. The reply is defined by the sensor

manufacturer but usually includes the sensor address, SDI-12 version, manufacturer’s name, and
sensor model information. Serial number or other sensor specific information may also be
included. Source:

SDI-12: A Serial-Digital Interface Standard for Microprocessor-Based Sensors

(see

References

[p. 1]).

Command:

aI!

Response:

allccccccccmmmmmmvvvxxx...xx<CR><LF>

Where

= sensor address

MetSENS-Series Compact Weather Sensors

Содержание MetSENS Series







































Результаты поиска

Содержание MetSENS Series

Отзывы:

Бренды по названию

Популярные бренды

Campbell MetSENS Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание MetSENS Series

Отзывы:

Бренды по названию

Популярные бренды