manualshive.com logo in svg
background image

7

WL6700 Series

www.chpower.com

After unpacking the unit, inspect carefully 
for any damage that may have occurred 
during transit. Check for loose, missing 
or damaged parts. Make sure to tighten 
fittings, bolts, etc., before putting unit 
into service. Check to be sure all supplied 
accessories are enclosed with the unit. In 
case of questions, damaged or missing 
parts, please call 1-800-543-6400 for 
customer assistance.

u  

Do not operate unit if damaged during 
shipping, handling or use. Damage may 
result in bursting and cause injury or 
property damage.

For your own safety, never operate unit 
until all assembly steps are complete and 
until you have read and understood the 
entire operator’s manual.

To reduce the risk of injury, if any parts are 
missing, do not attempt to assemble the 
air compressor until the missing parts are 
obtained and installed correctly.

ContentS In the CArton

Blow gun accessories

Handle with grip

Blow gun

Nylon recoil hose

(4) Self-tapping screws

Tire inflation valve 

u

  Operating Instructions and Parts 

Manual

u

  Warranty Card

ADDItIonAL IteMS not InCLuDeD

u

  Air Hose

u

  ANSI Z87 Eye Protection

u

  Hearing Protection 

u

  Other Personal Protective Gear as 

required

read & Follow All Instructions

Save these Instructions 

Do not Discard

Unpacking

Figure 2 - unpacking

Nylon 

recoil hose

Handle

Self-tapping 

screws

Blow gun

Blow gun 

accessories

Tire 

inflation 

valve

Содержание Reference Design





















Отзывы: