manualshive.com logo in svg
background image

14

Operating Instructions and Parts Manual

www.chpower.com

Operation (Continued)

Figure 17 - Safety valve

enD oF oPerAtIon/StorAge

1.  Turn compressor OFF at foot pedal ON/OFF switch.
2.  Unplug power cord from wall outlet and attach to clip that is molded on the side of 

the top shroud.

3.  Drain tank of condensation as outlined in the Drain Tank section below.
4.  Wearing safety glasses, drain tank of any remaining air pressure by pulling the 

ring on the safety valve.  Use other hand to deflect any fast moving air that may be 
directed towards your face.

5.  Store compressor in a cool, dry place. 

Maintenance

 

Disconnect power source then release all pressure from the  

  system before attempting to install, service, relocate or 

perform any maintenance. Service should be performed by an authorized service 
representative.

The compressor should be checked often for any visible problems and the 
following maintenance procedures should be performed each time the compressor is 
used.

ASMe SAFety VALVe

  Do not remove or attempt to adjust the safety valve!

Check the safety valve by performing the following steps: 

1.  Plug the compressor in and run until shut off pressure is reached (see Operating 

Procedure). 

2.  Wearing safety glasses, pull the ring on the safety valve to release pressure from 

compressor tank. Use your other hand to deflect fast-moving air from being 
directed toward your face.

3.  The safety valve should automatically close at approximately 40-50 psi. If the safety 

valve does not allow air to be released when you pull on the ring, or if it does not 
close automatically, it MUST be replaced. 

DrAIn tAnk

1.  Turn compressor off at foot pedal switch.
2.  Check air pressure in tank.  To properly drain tank of condensation, tank pressure 

should be between 20-60 psi.  Drain system will not work if there is no pressure 
in the tank.  If tank pressure is above 60 psi, drain tank by pulling the ring on the 
safety valve.  The safety valve should release air and then automatically close at 
approximately 40-50 psi.  

3.  Slowly turn easy drain knob, located below the tank gauge, to the left 

(counterclockwise) 

until fluid begins to fill drain cup.  Watch draining to make sure 

drain cup does not overflow.  If there is a lot of fluid in the tank, you may need to 
close drain knob by turning fully to the right 

(clockwise)

 then remove the drain cup 

to dispose of fluid.

4.  When fluid stops draining, close drain knob by turning all the way to the right 

(clockwise)

.

5.  Lift cup up and pull out to dispose of drained fluid.  Reinsert cup, making sure to 

secure in place.

Figure 18 - Draining tank

Tank Pressure 

Gauge

Easy-Drain 

Knob

Easy-Drain Cup

Fill Line

Содержание Reference Design





















Отзывы: