Cameron BARTON 580A Скачать руководство пользователя страница 9

Страница: 9 / 56

Model 580A Differential Pressure Switch

Section 2

Section 2—Installation

The instrument should be inspected at time of unpacking to detect any dam-

age that may have occurred during shipment.

IMPORTANT: The DPU was checked for accuracy at the factory. Do not change any of

the settings during examination or accuracy could be affected.

For applications requiring special cleaning/precautions, a polyethylene bag

is used to protect the instrument from contamination. This bag should be

removed only under conditions of extreme cleanliness.

Mounting/Piping/DPU Installation

Mount the instrument with four customer-supplied 5/16-in. (8-mm) bolts,

Grade 5 or greater, torqued to 17 ft/lbs. Mounting structures should be

designed to avoid resonance and/or minimize resulting amplification below

33 Hz. Response spectra at mounting surface of the instrument shall not

exceed those in the R3-580A-29 Qualification Report. Interfacing process

tubing and conduit shall be supported by the same mounting as the DP instru-

ment base in order to minimize relative motion of the DP instrument and

connections.

Dimensional drawings are provided on

Section 5—Dimensional Drawings,

page 33

See

Appendix A, page A-1

for Model 224 DPU installation and mainte

nance information.

Electrical Connection

Units are supplied with dual alarm switches. The direct-set switch contacts

are adjustable over 10% to 90% of the scale range.

The high switch and low switch set point adjustment procedures are covered

Changing Switch Set Point, page 20

For physical location of switches, see Figures 1.1 and 1.2,

page 4

Switch Use

Switch contact life is influenced by various application conditions such as

temperature, humidity, airborne contamination, vibration, amount of plunger

travel, cycling rate, and rate of plunger travel (and others), as well as by the

electrical (circuit) characteristics.

Содержание BARTON 580A

























































Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды

Cameron BARTON 580A, Руководство пользователя

Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды